Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Caustic soda & soda ash

Caustic soda flakes 98% and 99% grades compared

What separates 98% and 99% caustic soda flakes: production route, chloride, iron and carbonate, and which applications need the higher grade.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of caustic soda flakes in a glass dish
On this page · 6 sections
  1. 01Where the difference comes from
  2. 02The parameters that differ
  3. 03Total alkalinity versus NaOH
  4. 04Which applications need 99%
  5. 05Where 98% is usually adequate
  6. 06Specifying your grade

Caustic soda flakes are usually offered as 98% or 99% NaOH. One percentage point looks trivial, and for many uses it is. But the figure is a proxy for how the product was made and for the impurities it carries, and those can matter a great deal in some processes. This guide explains what lies behind the two grades and how to pick between them.

Where the difference comes from

All flakes start as caustic solution from the electrolysis of salt brine, which is evaporated to 50%, then concentrated further to molten caustic and flaked on cooled rolls. The cell technology sets the impurity profile:

  • Membrane cells produce a caustic solution with very little salt carried over. Flakes made from membrane liquor are usually the 99% grade, with low chloride.
  • Diaphragm cells produce a weaker cell liquor that still contains a lot of salt. Much of it drops out during evaporation, but the finished caustic keeps noticeably more sodium chloride. Flakes from this route are typically sold as 98% or lower.

So when a buyer chooses 99% over 98%, the main gain is usually not the extra NaOH. It is lower chloride and, generally, a cleaner product overall.

The parameters that differ

Parameter98% grade (typical)99% grade (typical)Why it matters
NaOH, minimum98%99%Sets the dose per kilogram of active alkali
Sodium chlorideHigher; varies by producerLow, often a few hundred mg/kg or lessChloride drives pitting of stainless steel and affects some syntheses
Sodium carbonateSimilar limits; rises with poor storageSimilar limits; rises with poor storageReduces effective alkali; can form scale
IronUsually a little higherLowCauses colour in soaps, textiles and clear products
Other metalsNot always reportedOften reported in detailRelevant for food, pharmaceutical and electronics uses

Exact limits vary between producers and national standards, so compare offers on the full certificate of analysis, not on the headline percentage.

Total alkalinity versus NaOH

Check how the assay is expressed. Some certificates report total alkalinity, which counts carbonate as well as hydroxide and expresses the total as NaOH or Na₂O. Others report true NaOH, measured after the carbonate has been precipitated with barium chloride. A product can show 99% total alkalinity but noticeably less true NaOH if it carries carbonate. For an apples-to-apples comparison, ask for NaOH and Na₂CO₃ to be reported separately.

Which applications need 99%

  • Stainless steel systems and heat exchangers, where chloride accelerates corrosion, especially at elevated temperature.
  • Fine chemicals, pharmaceuticals and dyes, where chloride or iron may end up in the product or poison a reaction.
  • Clear or white consumer products, such as transparent soaps and liquid cleaners, where iron can cause discolouration.
  • Food processing and drinking water, which also need the appropriate certification, not just a high assay.
  • Ion-exchange regeneration, where chloride in the regenerant reduces the efficiency of anion resins.

Where 98% is usually adequate

General neutralisation of acidic effluent, laundry soap boiling, pulp and paper cleaning, metal degreasing and many textile scouring operations tolerate the higher chloride of a 98% product without trouble. Here the decision is mostly economic: compare the cost per kilogram of NaOH actually delivered rather than per kilogram of flakes.

The step from 98% to 99% is mostly about chloride and iron, not about the extra point of NaOH.

Specifying your grade

In your enquiry, give the minimum NaOH and the maximum chloride, carbonate and iron your process can accept, and say what the product is for. Ask for a lot-specific certificate of analysis and, for regulated uses, the relevant certification. Nuroil offers caustic soda flakes in the common grades from established producers; send your specification through request a quote.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote