Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Bitumen

Safe handling and heating temperatures for bitumen

Reference guide to bitumen temperature limits, storage, reheating, boil-over, fumes and burns, based on established industry guidance.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of a paved road leading to a bitumen terminal with tankers
On this page · 6 sections
  1. 01Maximum handling temperatures
  2. 02Storage temperatures
  3. 03Reheating and restarting tanks
  4. 04Boil-over, fire and gases
  5. 05Personal protection and burns
  6. 06What to ask your supplier

Most bitumen is stored, transported and used as a hot liquid. That makes temperature control the single most important safety and quality factor. Too cold and it will not pump; too hot and it creates fire risk, extra fumes and a damaged product. This guide summarises widely used industry guidance. Always follow the product SDS and your site's own risk assessment.

Maximum handling temperatures

European industry guidance sets the following ceilings:

  • Paving bitumen, including polymer modified grades: handled up to 200°C.
  • Industrial bitumen, such as oxidised grades: handled up to 230°C.
  • In all cases, keep bitumen at least 30°C below its flash point, or below any national limit if that is lower.

These limits exist mainly to prevent a flammable atmosphere forming in the headspace of heated tanks. Within this range, fume emissions are also expected to stay within workplace limits. The general rule is to use the lowest temperature that does the job.

Storage temperatures

Bitumen held hot for long periods hardens, forms deposits in the tank and gives off more fumes. Industry guidance therefore lowers the temperature for longer storage. For penetration grades it recommends:

GradeShort-term storage (under 1 month)Medium or long-term storage (over 1 month)
10/20 and 15/25135°C90°C
20/30130°C90°C
35/50125°C85°C

For polymer modified and speciality bitumens, ask the supplier, as their recommendations vary with the polymer and the grade.

Reheating and restarting tanks

  • Raise the thermostat in small steps of about 5–10°C to avoid local overheating around the heating coils.
  • Make sure the coils are fully covered by bitumen before heating; exposed coils can overheat the material and the tank headspace.
  • Check for water. Condensation can collect in a tank during a shutdown, and water meeting hot bitumen turns to steam instantly, causing violent foaming and boil-over.
  • Test the bitumen before use after a long shutdown, and record the reheating in a plant-level risk assessment.

Boil-over, fire and gases

Boil-over is one of the most serious hazards with hot bitumen. It happens when water, emulsion or a wet product is introduced into a tank above 100°C. Never load bitumen into a tank or tanker that may contain water, and confirm compatibility before switching a tank between products. Cutback grades need extra care because their solvents lower the flash point considerably.

Hot bitumen can also release hydrogen sulphide, which collects in tank headspaces and confined spaces. It is toxic and can deaden the sense of smell. Gas testing, ventilation and permit-to-work procedures are needed before tank entry or work over open hatches.

Personal protection and burns

Workers handling hot bitumen should wear heat-resistant gloves, face shields or goggles, long-sleeved flame-retardant clothing and safety boots, with cuffs worn over gloves and boots so hot material cannot run inside. Safety showers or clean water should be close to loading and discharge points.

If hot bitumen contacts skin, cool the area immediately with plenty of cool, clean running water and keep cooling while medical help is sought. Do not try to pull the bitumen off, as it may remove skin; medical staff will deal with it. Industry burns cards, available in many languages, give first-aid steps and can travel with the casualty to hospital.

Lowest workable temperature, no water anywhere near hot bitumen, and cooling first in any burn.

What to ask your supplier

For each grade, request an MSDS showing flash point and recommended handling and storage temperatures, and a certificate of analysis for each lot. For bulk deliveries, confirm the delivery temperature and that the receiving tank is dry and compatible. Nuroil supplies an MSDS on request and a CoA with every delivery for bitumen grades including polymer modified and oxidised products.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote