A pool flocculant, or floc, gathers the fine particles that make water cloudy into large, heavy clumps that sink. Typical liquid formulations are based on an aluminium coagulant, most often polyaluminium chloride or aluminium sulphate solution, frequently with a cationic polymer to build bigger floc. The offered product’s TDS and SDS give its exact composition.
It is a one-off treatment for badly cloudy water: dose with the pump running briefly, switch off, let the floc settle overnight, then vacuum it to waste so it bypasses the filter. For light haze with the filter running, a clarifier is the better choice.
Identity
Base
Aluminium salt or polymer
Type
Liquid flocculant
CAS
1327-41-9 (PAC), per SDS
Aluminium-based or polymer pool flocculantWhy Pool flocculant
Clears badly cloudy waterSettles heavy haze from algae kills, dust storms or start-up in one treatment.
Spares the filterThe settled floc is vacuumed to waste, so it does not clog sand or cartridge filters.
Fast turnaroundClear water usually overnight, then the pool is vacuumed and back in use.
Documented qualityEach offered product comes with its TDS, Certificate of Analysis and safety data sheet.
What Nuroil does on every order
Why choose flocculant from Nuroil?
Checked against the batch CoA
Active content, pH and density are reviewed on the batch certificate before loading.
Formulation stated
The base, its strength and the dose rate are confirmed on the TDS with the offer.
Sealed, labelled containers
Cans, drums and IBCs closed and labelled to the SDS.
One desk, firm offers
FOB, CFR or CIF from our Sharjah trade desk, usually within 24 hours.
02 TECHNICAL DATA
Technical specification.
Base
Polyaluminium chloride or aluminium sulphate solution, often with a cationic polymer, per TDSProducer formulation
Aluminium (as Al₂O₃), aluminium-based
Typically about 5–18%, by formulationEDTA titration
pH (as supplied)
About 2.5–4.5pH meter
Density at 20 °C
About 1.1–1.35 g/cm³Hydrometer
Appearance
Clear to slightly hazy, colourless to pale yellow liquidVisual
01ALUMINIUM-BASED
General pool floc
Polyaluminium chloride or alum solution, the common choice for heavy cloudiness.
02ALUMINIUM WITH POLYMER
Faster, bigger floc
An aluminium base with a cationic polymer that builds larger floc and settles faster.
03POLYMER
Aluminium-free
Cationic polymer flocculants where aluminium is not wanted, per TDS.
Selection guidance Tell us the pool sizes, the filter type and how cloudy the water gets, and we will confirm the formulation.
Both clear cloudy water. A flocculant settles particles to the floor; a clarifier gathers them for the filter.
Property
Flocculant
Clarifier
How it works
Settles to the floor
Gathers for the filter
Speed
Overnight
1–3 days
Work after dosing
Vacuum to waste
None
Pump
Off while settling
Running
Best suited to
Heavy cloudiness
Light haze, routine polish
03 HOW IT IS MADE
From aluminium salt to liquid floc.
Polyaluminium chloride is made by reacting aluminium hydroxide with hydrochloric acid under controlled basicity. The pool flocculant is blended from it, or from aluminium sulphate solution, with water and often a cationic polymer, then filtered and filled.
01
Aluminium salt
Polyaluminium chloride or aluminium sulphate solution is the base.
02
Blending
The base is diluted to strength, and a cationic polymer added where used.
03
Filtering
The liquid is filtered clear of insolubles.
04
Testing and filling
Each batch is tested for strength, pH and density and filled into cans, drums or IBCs.
04 APPLICATIONS
Where it clears water.
01
Cloudy pools
Settling heavy cloudiness to the floor for vacuuming to waste.
02
After algae and storms
Clearing dead algae, dust and debris after a shock or a sandstorm.
03
Pool start-up
Clearing fresh fill water that arrives cloudy.
04
Water features
Clearing ponds, fountains and decorative water, where suitable.
05 SAFETY & HANDLING
Acidic liquid. Protect your eyes.
This summary does not replace the Safety Data Sheet. Classification depends on the formulation; review the product SDS and site procedure before first handling.
Danger
H290 May be corrosive to metals (aluminium-based, per SDS).
H318 Causes serious eye damage (aluminium-based, per SDS).
UN
Not regulated or 3264, per SDS
Class
8 where regulated, per SDS
01
Protect your eyes
Aluminium-based flocculants are acidic and can cause serious eye damage; wear eye protection and gloves.
02
Corrosive to metals
Keep it in its plastic container and off bare steel and aluminium.
03
Away from alkalis and chlorine
Dose separately from soda ash, caustic soda and chlorine products, never mixed in a container.
04
Vacuum to waste
Run the floc to waste, not through the filter, and top up and rebalance the water afterwards.
05
Exposure response
Rinse eyes cautiously with water for several minutes, remove contact lenses, and seek medical attention.
Closed, shaded and frost-free.
Shelf lifeTypically 1–2 years
Liquid flocculants are stable kept closed, out of the sun and above freezing. Confirm the producer’s shelf life with the offer.
Keep containers closedReseal after use and keep the original label.
Shaded, above freezingOut of direct sun and away from heat; do not let it freeze.
Apart from alkalisAway from strong alkalis and chlorine products, and off bare metal.
First in, first outUse the oldest stock first and keep the batch label with each lot.
Plan documentation early.
HS code3824.99
CAS number1327-41-9
CAS number26062-79-3
TransportPer SDS
GHS
Aluminium-based grades typically serious eye damage (H318) and may be corrosive to metals (H290); per SDS
Transport
Often not regulated; some acidic grades ship as UN 3264, class 8, PG III; per SDS
Pool use
Confirm the product suits the local pool code and the filter type
National regulations
Confirm the destination’s chemical-import requirements
06 PACKING OPTIONS
Choose your packing.
Pack sizes, formulation and container loads depend on the producer; the offer confirms them.
Smaller orders
Cans and jerrycans
HDPE cans, commonly 1, 5, 20 or 25 litres, for pool companies and retail.
Typical liquid flocs are based on polyaluminium chloride or aluminium sulphate solution, often with a cationic polymer. Strength and additives vary by producer; the offered product’s TDS and SDS give the exact composition.
02Flocculant or clarifier?
Flocculant for heavy cloudiness, when you can switch the pump off and vacuum to waste. Clarifier for light haze, working through the filter with no vacuuming.
03How is it used?
Balance pH first, usually to about 7.2–7.6. Dose with the pump running for a short time, switch off and let it settle for 8–24 hours, then vacuum slowly to waste. Follow the product TDS for dose.
04Why vacuum to waste?
The floc is fine and sticky; sent through a sand or cartridge filter it clogs it or passes back into the pool.
05Does it affect pH?
Aluminium-based flocs are acidic and lower pH and alkalinity a little. Check and correct after treatment, for example with soda ash.
06What is the HS code?
Formulated flocculants are usually declared under HS 3824.99; aluminium-based solutions are sometimes declared under 2827.49 or 2833.22. Confirm with the product and destination.
07What documents come with a shipment?
A TDS, Certificate of Analysis and Safety Data Sheet, with the Certificate of Origin as required.
Include the type (aluminium-based or polymer), quantity, packing and destination for a tailored offer. We reply with a firm FOB, CFR or CIF offer, usually within 24 hours.