Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Bitumen

Viscosity grade and penetration grade bitumen: a cross-reference for tenders

An approximate cross-reference between VG, AC and penetration grades of bitumen, why no exact conversion exists and how to handle mixed specs.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of a glass capillary viscometer in a 60 °C water bath
On this page · 6 sections
  1. 01Why there is no exact conversion
  2. 02Approximate correspondence
  3. 03Which grade for which climate
  4. 04Handling a mixed specification
  5. 05Performance grades
  6. 06Enquiry checklist

Buyers frequently receive tenders written in one grading system while suppliers quote in another. A road authority may specify VG-30, a contractor may ask for 60/70, and an offer may arrive as AC-30. This guide gives the approximate correspondence between the systems and explains why it is only approximate.

Why there is no exact conversion

Each system measures a different property. Penetration grading uses a needle test at 25°C. Viscosity grading uses absolute viscosity at 60°C. Two binders with the same penetration can have different viscosities at 60°C, because bitumens from different crudes and refining routes change stiffness with temperature at different rates. So a 60/70 binder may fall into VG-30 or, occasionally, outside it.

That is also why viscosity grading was introduced: to control the property most closely tied to hot-weather performance rather than inferring it from a room-temperature test.

Approximate correspondence

The table below combines the replacements described by Indian refiners when IS 73 moved from penetration to viscosity grades, and the published 60°C bands of IS 73 and ASTM D3381.

VG grade (IS 73)60°C viscosity, poiseClosest AC gradeOlder penetration grade it replacedPenetration at 25°C, min under IS 73
VG-10800–1200AC-1080/10080
VG-201600–2400AC-20None directly60
VG-302400–3600AC-3060/7045
VG-403200–4800AC-4030/4035

Notes on the table:

  • Each VG grade shares its 60°C band with the AC grade of the same number, but the two standards are not interchangeable.
  • Other limits (flash point, 135°C viscosity, ageing tests) differ between IS 73 and ASTM D3381.
  • VG-40 is sometimes loosely compared with 40/50. Indian refiners describe it as replacing the old, harder 30/40 grade.

Which grade for which climate

IS 73 links each viscosity grade to the seven-day average maximum air temperature over the design period, which gives a useful way to think about all three systems:

7-day average max air temperatureVG gradeTypical penetration counterpart
Below 30°CVG-1080/100 or softer
30–38°CVG-20Between 80/100 and 60/70
38–45°CVG-3060/70
Above 45°CVG-4040/50 or 30/40

Climate is only one input. Traffic volume, loading speed and the layer in the pavement also shift the choice, which is why a hot-region project may still use VG-30 on open carriageway and VG-40 only at junctions and climbing lanes.

Handling a mixed specification

  1. Find the governing document. The contract specification decides; a grade named in a cover letter does not override it.
  2. Certify to that system. If the specification says VG-30 to IS 73, the CoA should report IS 73 tests, not just penetration.
  3. Ask for dual testing when needed. Where a project accepts either system, a certificate showing both 60°C viscosity and penetration with softening point lets the engineer judge the binder directly.
  4. Check the actual values. A lot near the top of VG-30 behaves differently from one near the bottom; compare numbers, not labels.
  5. Get approval in writing before substituting one system for another.
Use a cross-reference to shortlist products, never to certify them.

Performance grades

Some tenders now name performance grades such as PG 64-22 or PG 70-10 instead of either system. These are set from the expected high and low pavement temperatures and include tests on aged binder, so they do not map neatly onto VG or penetration grades either. A conventional VG-30 or 60/70 binder may meet a particular PG grade, but that can only be confirmed by running the PG tests on the actual product.

Enquiry checklist

Quote the grade and standard exactly as specified, state whether an alternative system is acceptable, and request a CoA covering the governing standard's full table. Nuroil supplies both viscosity grade and penetration grade bitumen and can match offers to the standard your tender names. Send your specification via request a quote.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote