Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read6 sections

Knowledge centre · Waterproofing & construction

Storing HPMC: moisture, shelf life and lump prevention

How to store HPMC powder for construction use: moisture control, warehouse conditions, re-testing older stock and avoiding lumps in the mixer.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of a roof being waterproofed with bitumen membrane
On this page · 6 sections
  1. 01Keep it dry
  2. 02Keep it cool and protected
  3. 03Shelf life and re-testing
  4. 04Preventing lumps
  5. 05Dust and safety
  6. 06Packing and documents to request

HPMC is a stable powder when kept dry, but poor storage can still cause problems at the plant: caked bags, drifting viscosity, lumps in the mixer and dust in the warehouse. Because HPMC is added in small quantities, any change in its performance shows up directly in the finished mortar. This article covers good storage and handling practice.

Keep it dry

Cellulose ethers take up moisture from humid air. Pharmacopoeial specifications for hypromellose limit loss on drying to 5.0% at 105 °C, and construction-grade data sheets also state a maximum moisture content. Powder that absorbs water can cake and becomes harder to dose accurately, and moisture adds weight that is not active product.

  • Store bags indoors, on pallets off the floor, away from walls that may sweat.
  • Keep bags closed until use and reseal part-used bags tightly or transfer the remainder to a sealed container.
  • In humid coastal climates, avoid leaving pallets in open-sided sheds or on quaysides longer than necessary.

Keep it cool and protected

Store away from direct sun, heat sources and strong oxidising agents. Stack pallets to a height that does not crush the lower bags; multi-wall paper bags with a polyethylene liner are common and can split if overloaded. Rotate stock on a first-in, first-out basis.

Shelf life and re-testing

There is no single shelf life for HPMC; producers state a recommended storage period or re-test date on their documentation, typically counted from manufacture and conditional on correct storage. Check the CoA or technical data sheet for the figure that applies to the grade you buy. If stock passes that date, or if storage has been poor, re-test before use rather than discarding automatically:

  1. Measure moisture and compare with the specification.
  2. Measure viscosity of a 2% solution using the same method and conditions as the supplier's CoA.
  3. Run a quick water retention or open time check in your standard mortar.

If results are within specification, the material can normally be used; if not, consult the supplier.

Preventing lumps

Dry cellulose ether tends to gel at the surface when it meets water, wrapping dry powder in a sticky skin and forming lumps that dissolve slowly. In a dry-mix mortar this is largely avoided because the HPMC is dispersed among sand and cement before water is added. Problems arise when HPMC is added to water on its own, for example in a liquid product or a test solution.

  • In dry mixes, blend HPMC thoroughly with the other dry components before water is added.
  • For solutions, use a surface-treated (delayed-dissolution) grade, or disperse the powder in hot water above its gel temperature and then cool while stirring, as the producer recommends.
  • Do not use caked powder without breaking and sieving; lumps that enter a dry mix will not disperse evenly.

Dust and safety

HPMC is generally of low hazard, but like other fine organic powders it can form combustible dust clouds, and dust spills make floors slippery when wet. Use local exhaust ventilation at tipping points, avoid dust accumulation, keep ignition sources away, and wear dust masks and eye protection as the SDS directs. Clean spills by vacuum or sweeping rather than washing down.

IssueCauseRemedy
Caked bagsHumidity, damaged liners, overstackingDry indoor storage, sound packaging, limited stacking
Viscosity driftLong or poor storageRe-test before use; rotate stock
Lumps in mixer or solutionPoor dispersion, caked powderPre-blend dry, sieve, use suitable grade
DustOpen tipping, spillsExtraction, housekeeping, PPE per SDS

Packing and documents to request

When ordering, specify the bag size and type, palletising and wrapping, and whether you need moisture-barrier liners for humid transit. Ask for the CoA with manufacturing date and recommended storage period, the technical data sheet and the SDS. Nuroil can supply HPMC on request for construction chemical plants; contact us through the contact page.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote