Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Industrial chemicals

Storing and handling industrial ethanol: flammability, static and ventilation

Conservative practice for storing and transferring industrial ethanol: ignition control, earthing and bonding, ventilation, spills and fire response.

Written by the Nuroil trade desk, Sharjah

On this page · 6 sections
  1. 01Key hazard properties
  2. 02Storage
  3. 03Static electricity, earthing and bonding
  4. 04Ventilation and exposure
  5. 05Spills and fire
  6. 06Supply and documentation

Ethanol is familiar enough that its hazards are easy to underestimate. Industrial grades from 95% to 99.9% are highly flammable liquids that give off ignitable vapour at ordinary room temperature. This guide summarises conservative storage and handling practice. It is general information only; always follow the supplier's safety data sheet (SDS), your local fire code and your site's risk assessment.

Key hazard properties

PropertyTypical valueWhy it matters
Flash point (closed cup)About 12–14 °CVapour can ignite at normal indoor temperatures
Flammable range in airAbout 3.3–19% by volumeA wide range; small leaks can form ignitable mixtures
Vapour density (air = 1)About 1.6Vapour sinks and spreads along floors and into drains and pits
Auto-ignition temperatureAbout 363 °CHot surfaces can ignite vapour without a flame
GHS hazard statementsH225, H319Highly flammable liquid and vapour; causes serious eye irritation

Water dilution lowers the hazard only slowly. Mixtures used in sanitisers and cleaners remain flammable and should be treated with the same care.

Storage

  • Store in a cool, dry, well-ventilated area designated for flammable liquids, away from heat, sparks, open flames and direct sun.
  • Keep containers tightly closed when not in use. Open containers release vapour and, for anhydrous grades, absorb moisture.
  • Segregate from strong oxidisers, strong acids, acid anhydrides and acid chlorides.
  • Provide secondary containment (bunds or spill pallets) sized to the largest container, and keep drains in the area sealed or routed to a safe collection point.
  • Use electrical equipment and lighting rated for the hazardous area classification of the store.
  • Respect local limits on quantities in production areas; bring in only what is needed for the shift.

Static electricity, earthing and bonding

Flowing ethanol and moving containers can build up static charge. A spark from an ungrounded drum, funnel or operator can ignite vapour at the container mouth. Good practice includes:

  • Earthing fixed tanks and pipework, and checking continuity periodically.
  • Bonding drums, IBCs and receiving vessels together before transfer, and earthing the set.
  • Using conductive or static-dissipative hoses and metal funnels that are bonded.
  • Avoiding splash filling: fill from the bottom or with a dip pipe that reaches near the base.
  • Choosing IBCs designed and certified for flammable liquids if IBCs are used.

Ventilation and exposure

Ethanol has a relatively high occupational exposure limit (often 1000 ppm as an eight-hour average), but vapour concentrations near open mixing tanks can still be high enough to cause irritation and to approach the lower flammable limit. Local exhaust at mixing and filling points, plus general ventilation at floor level, addresses both concerns. Use safety glasses or goggles to protect eyes from splashes, and chemical-resistant gloves for prolonged contact.

Treat every transfer as a potential ignition event: no open flames, bonded containers, ventilation running, and a spill kit within reach.

Spills and fire

  • Remove ignition sources, ventilate, and stop the leak if it is safe to do so.
  • Contain with non-combustible absorbent; use spark-proof tools; keep runoff out of drains and watercourses.
  • Ethanol fires burn with a pale, sometimes nearly invisible flame in daylight. Use alcohol-resistant foam, dry chemical or carbon dioxide; water spray can cool exposed containers. Ordinary foams may break down on contact with alcohols.
  • Closed containers exposed to fire can rupture. Cool them from a distance and follow your emergency plan.

Supply and documentation

Before the first delivery, make sure your store, transfer equipment and permits match the packing you intend to buy. Ask your supplier for the current SDS in the language your staff use, and the certificate of analysis for each lot. Nuroil provides a CoA with every delivery and the SDS on request. Discuss packing and delivery via our quote request form.

KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote