Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read5 sections

Knowledge centre · Industrial chemicals

Industrial ethanol grades and specification parameters explained

9%, and what each line on an ethanol certificate of analysis means.

Written by the Nuroil trade desk, Sharjah

On this page · 13 sections
  1. 01Common grades
  2. 02Parameters on a certificate of analysis
  3. 03Ethanol content
  4. 04Water
  5. 05Methanol
  6. 06Other volatile impurities
  7. 07Acidity or alkalinity
  8. 08Non-volatile residue (evaporation residue)
  9. 09Appearance, colour and odour
  10. 10UV absorbance
  11. 11Denatured ethanol
  12. 12Sampling and verification
  13. 13Building your enquiry

Ethanol is sold under many names: rectified spirit, extra neutral alcohol, absolute alcohol, dehydrated alcohol, technical ethanol, denatured alcohol. Behind the names, buyers mainly need to know three things: how much ethanol is present, what else is present, and whether a denaturant has been added. This guide sets out the common industrial grades and explains the parameters you will see on a specification sheet.

Common grades

GradeTypical ethanol contentNotes
Technical / industrial 95%About 95% v/vGeneral solvent and cleaning use; impurity limits set by supplier
Rectified / pharmacopoeial 96%95.1–96.9% v/vPharmacopoeial range for 96% ethanol; tight impurity limits
Anhydrous 99.5%99.5% v/v minDehydrated beyond the azeotrope; suits most water-sensitive uses
Anhydrous 99.9%99.9% v/v minLaboratory, analytical and demanding synthesis work
DenaturedAny of the above plus denaturantDenaturant type and level must be stated

Pharmacopoeial ethanol 96% is defined as 95.1 to 96.9% by volume at 20 °C, equivalent to about 92.6 to 95.2% by mass, with water making up the balance. Always check whether a figure is by volume or by mass.

Parameters on a certificate of analysis

Ethanol content

Usually measured by density (relative density or specific gravity) at a reference temperature, or by gas chromatography. Because density changes with temperature, the certificate should state the reference temperature, normally 20 °C.

Water

For anhydrous grades, water is measured directly by Karl Fischer titration and reported as a maximum percentage or in ppm. For 96% grades, water is effectively the remainder.

Methanol

Methanol is a natural by-product of fermentation and a possible contaminant. It is measured by gas chromatography. Supplier specifications for pharmacopoeia-compliant 96% ethanol commonly show 200 ppm or less. Hygiene and pharmaceutical users should treat methanol as a critical parameter.

Other volatile impurities

Acetaldehyde, acetal, higher alcohols (fusel oils) and esters affect odour and can indicate distillation quality. Pharmacopoeial tests limit these individually and in total. Benzene, where specified, is limited to very low levels such as 2 ppm.

Acidity or alkalinity

Expressed as acetic acid or by titration. Elevated acidity can come from oxidation in storage or contamination and may affect sensitive formulations.

Non-volatile residue (evaporation residue)

The mass left after evaporating a sample. It picks up dissolved contaminants from tanks, drums or hoses and matters for cleaning and coating uses.

Appearance, colour and odour

Ethanol should be clear and colourless, with no foreign odour. Colour may be measured on a platinum-cobalt (Hazen) scale. A yellow tint or unusual odour is a reason to hold a delivery and investigate.

UV absorbance

Pharmacopoeial grades limit absorbance at specified wavelengths, which detects trace aromatic and carbonyl impurities.

Denatured ethanol

A denatured grade should state the denaturant and its concentration. The denaturant affects odour, toxicity, compatibility and sometimes the transport description. Users making products for skin contact must make sure the denaturant is suitable for that use; methanol-denatured spirit is not.

Write your specification around the parameters your process is sensitive to. A long certificate is not useful if it omits the one impurity that matters to you.

Sampling and verification

Ethanol content and water can drift in storage, especially in anhydrous grades exposed to humid air. Take samples from sealed containers, use clean glass bottles, and test on receipt for density and, where relevant, water and methanol. Keep a retained sample from each lot until the product made with it is released.

Building your enquiry

List the grade, the standard (pharmacopoeia or internal), limits for water, methanol and any other critical impurities, whether denaturing is required or forbidden, packing and annual volume. Ask for a lot-specific certificate of analysis and the current SDS. Nuroil provides a CoA with every delivery and can arrange certificate of origin and third-party inspection on request; send details through the quote request form.

KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote