Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read5 sections

Knowledge centre · Industrial chemicals

Ethanol as a solvent in pharmaceutical and industrial processes

Why ethanol is chosen as a process solvent for extraction, crystallisation, coatings and cleaning, and what limits its use.

Written by the Nuroil trade desk, Sharjah

On this page · 9 sections
  1. 01What makes ethanol a useful solvent
  2. 02Typical process uses
  3. 03Extraction
  4. 04Crystallisation and purification
  5. 05Coatings, inks and binders
  6. 06Cleaning and equipment rinsing
  7. 07Limits and trade-offs
  8. 08Solvent recovery
  9. 09Specifying ethanol for process use

Ethanol is one of the most widely used process solvents in industry. It dissolves a broad range of polar and moderately non-polar substances, mixes with water in all proportions, evaporates readily, and has comparatively low toxicity. These properties make it a default choice in pharmaceutical manufacture, natural-product extraction, coatings and cleaning. This article looks at why it works so well and where its limits lie.

What makes ethanol a useful solvent

An ethanol molecule has a short hydrocarbon chain and a hydroxyl group. The hydroxyl group lets it hydrogen-bond with water and polar compounds, while the ethyl chain gives it some affinity for oils, resins and less polar molecules. In practice that means ethanol can carry substances that water alone cannot dissolve, and it can be blended with water to tune solvent strength.

  • Boiling point around 78 °C: easy to remove by evaporation or distillation and to recover for reuse.
  • Full miscibility with water: allows graded water–ethanol mixtures for extraction and washing.
  • Relatively low toxicity: workplace exposure limits for ethanol are far higher than for many other organic solvents.
  • Available in pharmacopoeial grades: suitable where residues end up in a medicine or cosmetic.

Typical process uses

Extraction

Ethanol and water–ethanol mixtures are used to extract active compounds, flavours and fragrances from plant material. Changing the water ratio changes which compounds come out, so formulators often specify a particular strength rather than simply "ethanol".

Crystallisation and purification

Many pharmaceutical intermediates and active ingredients are dissolved in hot ethanol and crystallised on cooling, or precipitated by adding water as an anti-solvent. Here water content and impurities in the incoming ethanol directly affect yield and crystal form, so lots must be consistent.

Coatings, inks and binders

Ethanol is used alone or with esters and ketones to dissolve resins such as shellac, nitrocellulose and some polyamides, and in tablet coating solutions. Its evaporation rate is moderate, which helps film formation.

Cleaning and equipment rinsing

Ethanol removes oils, fingerprints and many organic residues and leaves little behind when high-purity grades are used. It is also used to rinse and dry equipment, since it carries water away as it evaporates.

Limits and trade-offs

Ethanol is not the right answer for every process. Its main drawbacks are:

  • Flammability: it is a highly flammable liquid with a flash point near 13 °C, so plants need ignition control, earthing and suitably rated electrical equipment.
  • Reactivity of the hydroxyl group: it can react with acid chlorides, anhydrides and some strong reagents, so it is unsuitable for some synthesis steps.
  • Water pick-up: anhydrous ethanol absorbs moisture from air, which can upset moisture-sensitive processes.
  • Denaturants: if denatured ethanol is used, the denaturant enters the process and may need to be removed or justified.
The best solvent grade is the one whose water content and impurity profile your process has been validated with, lot after lot.

Solvent recovery

Because ethanol is easy to distil, many plants recover and reuse it. Recovered solvent will usually contain more water and process-specific impurities, and it settles at the azeotrope near 95–96% unless further dried. Users who blend recovered and fresh ethanol should test the mixture against their in-house specification before each use, and keep recovered solvent out of products where a pharmacopoeial grade is required unless the recovery process has been validated.

Specifying ethanol for process use

When enquiring, state the strength (for example 96% or 99.9%), whether it must be undenatured, any pharmacopoeial or internal standard, and limits for water, methanol, acidity and non-volatile residue. Indicate expected volumes, since this decides whether drums, IBCs or ISO tanks make sense. Nuroil sources from established producers, provides a certificate of analysis with every delivery, and can supply SDS and arrange third-party inspection on request. Use our quote request form or contact us to discuss a specification.

KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote