Ethanol is the active ingredient in most alcohol-based hand rubs, so the quality of the ethanol you buy decides the quality of the product you sell. Sanitiser makers need to think about three things: the strength of the incoming ethanol, which denaturant (if any) it carries, and whether it is free of harmful contaminants such as methanol.
Starting strength and final concentration
Hand rubs are made by diluting a concentrated alcohol with purified water and adding a humectant to protect skin. The WHO's published local-production formula, for example, starts from 96% ethanol and dilutes it to a final 80% by volume, with small amounts of glycerol and hydrogen peroxide. A second WHO formula uses isopropyl alcohol at 75%.
Later laboratory work found that these original recipes did not meet a demanding European test for surgical hand preparation, while modified versions with ethanol at 80% by weight and less glycerol did. The practical lesson for buyers is that final alcohol content needs to be calculated and checked carefully, and that "percent" must always be qualified as volume or weight. A 96% v/v ethanol is about 93.8% w/w, and the difference becomes significant when you dilute.
- Use a starting grade with a known, certified ethanol content, typically 95–96% or 99.5%+.
- Measure density or alcohol content of each incoming lot rather than relying only on the label.
- Check the final product, since mixing alcohol and water causes slight volume contraction.
Why denaturants matter
Ethanol for non-beverage use is often denatured, meaning a small amount of another substance is added to make it unfit to drink. Some regulators require it for sanitisers specifically, because a bitter or unpleasant taste deters accidental swallowing by children. Common denaturing agents include isopropyl alcohol, methyl ethyl ketone, tert-butyl alcohol and very bitter compounds such as denatonium benzoate.
The denaturant becomes part of your formula, so it must be acceptable for repeated skin contact and compatible with fragrance, gels and packaging. A denaturant that is fine in a cleaning fluid may be unsuitable on hands. Before buying, confirm with your regulator which denaturant formulas are permitted for topical products in your market.
Never use methanol-denatured alcohol in a product for skin. Methanol is toxic through skin absorption and inhalation as well as by mouth.
Methanol and other contaminants
Methanol is the contaminant regulators watch most closely. Some sanitisers on the market have been found to contain methanol, either through substitution or contaminated raw material. The US regulator, for example, asks manufacturers to test each lot of ethanol or isopropyl alcohol for methanol when it is bought from another source, using the pharmacopoeial alcohol test method, and treats more than 630 ppm methanol as evidence of contamination. Its final guidance extends this testing to all products made with pharmaceutical alcohols. Other markets have their own limits, but the principle of lot-by-lot testing is widely applicable.
Pharmacopoeial grades also limit benzene, acetaldehyde, acetal and total volatile impurities. Supplier specifications for 96% ethanol meeting several pharmacopoeias commonly show methanol at or below 200 ppm and benzene at or below 2 ppm. Ethanol from unknown or poorly documented sources should not be used for hygiene products.
Handling in a sanitiser plant
Ethanol and finished sanitisers are highly flammable liquids. Mixing areas need ventilation, earthed and bonded vessels and drums, no open flames or hot work during production, and electrical equipment rated for flammable atmospheres. Keep quantities in the filling area to the minimum needed for the shift. Follow the product SDS and local fire regulations for storage limits.
What to specify when buying
- Ethanol content (v/v and w/w) and the grade or standard it must meet.
- Undenatured, or denatured with a named denaturant suitable for topical use.
- Maximum methanol, benzene, acetaldehyde and non-volatile residue.
- Packing size that matches your batch size, to limit open-container time.
Ask for a lot-specific certificate of analysis and the SDS, and arrange independent testing if your market requires it. Nuroil provides a CoA with every delivery and can arrange third-party inspection on request; send your specification via the quote request form.
