Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read6 sections

Knowledge centre · Industrial chemicals

Ethanol 96% or anhydrous 99.9%: which grade does your process need?

9% ethanol are made differently, and how to decide which one a formulation or process actually needs.

Written by the Nuroil trade desk, Sharjah

On this page · 6 sections
  1. 01Why 96% is a natural ceiling
  2. 02When 96% is the right choice
  3. 03When you need anhydrous
  4. 04The hidden cost of anhydrous ethanol
  5. 05Purity is not only about water
  6. 06What to put in your enquiry

Buyers of industrial ethanol usually meet two headline grades: rectified ethanol at around 95 to 96% by volume, and anhydrous (absolute) ethanol at 99.5 to 99.9%. They look identical in a drum, they carry the same transport classification, and they are often quoted side by side. Yet they are made by different routes, behave differently in storage and suit different jobs. Choosing the wrong one either wastes money or causes a process problem.

Why 96% is a natural ceiling

Ethanol and water form an azeotrope: a mixture that boils at a single temperature with vapour and liquid of the same composition. For ethanol and water this happens at roughly 95.6% ethanol by mass, boiling at about 78.2 °C. Once a still reaches that point, further distillation cannot separate the two. That is why rectified ethanol, the standard product of a distillation column, sits at about 95 to 96% by volume with the balance water.

To go beyond the azeotrope, producers add a separate dehydration step. The most common route today passes ethanol vapour through beds of 3A molecular sieve, a synthetic zeolite whose pores admit water molecules but exclude ethanol. The beds are cycled between adsorbing and regenerating. Older plants used azeotropic distillation with an entrainer, which is more energy-intensive. Either way, anhydrous ethanol carries an extra processing cost compared with rectified product.

When 96% is the right choice

Many applications dilute ethanol with water anyway, so paying to remove the last 4% makes little sense. Typical uses for 95 to 96% grades include:

  • Hand sanitisers and surface disinfectants, where the finished product is often 60 to 80% ethanol in water.
  • Cleaning fluids, window and glass cleaners, and general-purpose solvent blends.
  • Extraction of plant materials and many pharmaceutical processes, where a pharmacopoeial 96% grade is specified.
  • Perfumery and cosmetic bases, where a small water content is acceptable or even wanted.

When you need anhydrous

Water matters when it takes part in, or interferes with, a reaction or a formulation. Situations where buyers typically specify 99.5% or 99.9% ethanol include:

  • Chemical synthesis where water would hydrolyse a reagent or shift a reaction equilibrium, for example in esterification or with moisture-sensitive intermediates.
  • Blending with non-polar solvents, oils or resins, where the water in 96% ethanol can cause haze or phase separation.
  • Laboratory and analytical work, and some electronics cleaning, where residue and water spots must be minimised.
  • Pharmaceutical processes that call specifically for dehydrated alcohol in their master formula.
Point of comparisonRectified 95–96%Anhydrous 99.5–99.9%
How it is madeDistillation and rectificationRectification plus dehydration (usually molecular sieve)
Water contentAbout 4–5% by volumeTypically 0.1–0.5% or lower
Behaviour in storageStable water contentPicks up moisture from air if containers are left open
Typical usesSanitisers, cleaners, extraction, cosmeticsSynthesis, solvent blends, analytical work

The hidden cost of anhydrous ethanol

Anhydrous ethanol is hygroscopic: it draws water vapour from the air. A drum opened repeatedly in a humid store can drift away from its certificate value over time. If a process genuinely needs low water, plan for sealed containers, nitrogen blanketing on bulk tanks, dry-air breathers, and a water test (usually Karl Fischer titration) on receipt and before use. If those controls are not practical, it may be more honest to specify 99.5% rather than 99.9% and write the process around it.

Specify the lowest water content your process truly needs, then put the storage controls in place to keep it there.

Purity is not only about water

Two lots with the same ethanol percentage can still differ in methanol, higher alcohols, aldehydes, acidity and non-volatile residue. For hygiene and pharmaceutical use these impurities often matter more than a few tenths of a percent of water. Denatured grades add a further variable, because the denaturant itself becomes part of your formulation.

What to put in your enquiry

State the grade (96% or 99.5/99.9%), whether it must be undenatured or denatured (and with what), the standard it must meet (for example a pharmacopoeia or an internal specification), the end use, and the packing. Ask for a certificate of analysis showing ethanol content, water, methanol and other impurities. Nuroil supplies a CoA with every delivery and can arrange an SDS and third-party inspection on request. Send the details through our quote request form.

KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote