Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read7 sections

Knowledge centre · Industrial chemicals

SLES 70% and 28% specification parameters explained

A reference to each parameter on an SLES 70% or 28% specification sheet: active matter, unsulphated matter, salts, pH, colour, 1,4-dioxane and more.

Written by the Nuroil trade desk, Sharjah

On this page · 7 sections
  1. 01Identity
  2. 02Main parameters
  3. 03Reading the numbers for a 28% grade
  4. 04Paste and liquid behaviour
  5. 05Preservation status
  6. 06Typical documents
  7. 07Writing the specification into your enquiry

A specification sheet for sodium lauryl ether sulphate usually lists eight to twelve parameters. Each one tells the formulator something about how the material will perform or how consistent it will be from lot to lot. This guide explains what each parameter means and why it matters, with typical ranges drawn from published producer data where they are well established.

Identity

SLES is the sodium salt of a sulphated, ethoxylated fatty alcohol, usually based on C12 to C14 alcohols. The cosmetic ingredient name is sodium laureth sulphate. A specification should state:

  • Degree of ethoxylation: the average number of ethylene oxide units per molecule, most commonly 2 (often written 2EO), with 1EO and 3EO grades also made. It affects foam, mildness, water solubility and salt thickening.
  • Alcohol source: natural (from vegetable oils) or synthetic. Some buyers specify one or the other.
  • CAS number: SLES appears under more than one CAS number depending on the chain length and the producer's registration, so match the number to your regulatory files.

Main parameters

ParameterWhat it measuresWhy it matters
Active matter, %Content of anionic surfactant, usually by two-phase titrationThe basis for price, dosing and comparison. Typically about 68 to 72% for the 70% grade.
Unsulphated matter, %Ethoxylated alcohol that did not sulphate, plus other non-ionic organicsHigh values reduce performance and can affect odour and clarity. Producer limits are commonly around 3 to 3.5% maximum on the 70% grade.
Sodium sulphate, %Inorganic salt from neutralisationAffects viscosity, salt curve and clarity at low temperature. Commonly limited to about 1.5% maximum on the 70% grade.
Sodium chloride, %Inorganic chlorideShifts the salt thickening curve.
pH (of a stated dilution)Acidity or alkalinity, measured on a 1% or 10% solutionLow pH indicates possible hydrolysis; affects stability and final product pH.
ColourMeasured on a diluted solution by Klett, Hazen or similar scaleImportant for clear and water-white products.
1,4-dioxane, ppmBy-product of ethoxylation and sulphationNeeded for finished-product limits in many markets.
Appearance and odourVisual and sensory checkPaste or liquid, clear to slightly yellow, no off odour.
Microbiological countTotal viable count, yeasts and mouldsRelevant for personal care, particularly for the 28% liquid.

Reading the numbers for a 28% grade

Many parameters on a 28% sheet are stated on the product as supplied, which means they look smaller simply because there is more water. Unsulphated matter of 1.2% in a 28% product is roughly equivalent to 3% in a 70% product. When comparing a 28% offer with a 70% offer, convert parameters to a "per 100% active" basis:

Value on active basis = value as supplied × 100 ÷ active matter %.

The same applies to price: divide the price by the active matter fraction to compare cost per kilogram of surfactant.

Paste and liquid behaviour

Producer literature for a 2EO grade describes the 70% product as a flowable paste, transparent to yellowish, and notes that diluted solutions are liquid and stable up to about 28% active matter. At intermediate concentrations above about 30% the material forms stiff gel phases. Viscosity of the 70% paste is not always specified, because it is shear-dependent and hard to measure meaningfully; when it is, check the method and temperature.

Preservation status

Some SLES grades are supplied unpreserved, others with a preservative, usually in the 28% liquid. The preservative, if any, must be compatible with the buyer's finished-product regulations, so ask which is used and at what level.

Typical documents

  • Technical data sheet with the full specification and test methods
  • Certificate of analysis for each lot, with lot number and production date
  • Safety data sheet
  • Certificate of origin and, if needed, third-party inspection report
  • Statements on 1,4-dioxane, alcohol source or other customer requirements

Writing the specification into your enquiry

List the grade (70% or 28%), degree of ethoxylation, active matter range, maximum unsulphated matter, sodium sulphate, 1,4-dioxane and colour, and the packing. Nuroil supplies SLES on request with a CoA for every delivery; send the details through the quote form.

KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote