Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read7 sections

Knowledge centre · Industrial chemicals

Diluting SLES 70% paste and avoiding the gel phase

A practical reference for diluting SLES 70% paste: why gels form, the order of addition, temperature, mixing equipment and how to rescue a gelled batch.

Written by the Nuroil trade desk, Sharjah

On this page · 7 sections
  1. 01Why SLES gels on dilution
  2. 02Rule one: paste into water
  3. 03Recommended method
  4. 04Equipment notes
  5. 05Alternative method with salt brine
  6. 06Rescuing a gelled batch
  7. 07Supply considerations

SLES 70% is the most economical way to buy the surfactant, but it is unforgiving if diluted carelessly. A batch that is stirred slowly with water poured on top can turn into a solid, rubbery gel that stalls agitators and blocks pipes. This guide explains why that happens and sets out methods that work.

Why SLES gels on dilution

Surfactant molecules in water arrange themselves into structures that depend on concentration. At low concentration they form separate micelles and the solution is liquid. As the concentration rises, the micelles pack into ordered phases, first hexagonal, then cubic and lamellar arrangements. Some of these are extremely viscous.

For a typical 2EO SLES, producer data show:

Active matterBehaviour
Up to about 28%Liquid, stable solution, easily pumped
Intermediate, above about 30%Gel phases with very high viscosity; hard or impossible to pump with ordinary equipment
About 70%Flowable paste; pumpable with suitable pumps

When water is added to the paste, the whole mass passes through the gel region. Viscosity first rises steeply, and only falls again once the concentration drops below about 30%. Equipment suppliers recommend keeping the final concentration at or below 27% for this reason.

Rule one: paste into water

The most important rule is to add the concentrate to the water, not water to the concentrate. When paste is fed into a larger volume of moving water, each portion dilutes quickly through the gel region and the bulk stays liquid. When water is poured onto paste, the mixture at the interface forms a gel skin that stops further water penetrating, and lumps remain.

Recommended method

  1. Charge the water first. Calculate the water needed to reach the target concentration, usually 25 to 27% active, and charge it to the tank.
  2. Bring to the right temperature. A process temperature of about 25 to 35 °C is commonly recommended. Cold water slows dissolution; very hot water is not needed for standard dilution.
  3. Start strong mixing. High-shear in-line or bottom-entry mixers work best. A recirculation loop that takes water from the tank and injects paste just upstream of an in-line mixer is a common batch arrangement.
  4. Feed the paste steadily. Add at a rate the mixer can disperse. Pausing for long periods lets local gel zones form.
  5. Avoid air. Entrained air raises viscosity sharply and creates foam. Keep the mixer submerged, avoid splashing and use closed systems where possible.
  6. Dilute before adding thickeners. Add salt and other viscosity builders only after dilution is complete, and add salt as a solution, not as crystals.
  7. Check and adjust. Measure active matter and pH on the diluted batch before use or storage.

Equipment notes

  • Pumps: positive-displacement types, such as lobe, gear or progressive cavity pumps, handle paste and any gel better than centrifugal pumps.
  • Materials: stainless steel 316 is commonly specified for wetted parts.
  • Pipework: keep paste lines short and wide, with as few bends as practical. Trace-heating of paste lines is used in some plants to keep the paste mobile in cold weather.
  • Continuous systems: in-line systems meter paste and water together into a multi-stage high-shear mixer with flow meters controlling the ratio, giving a consistent output concentration in one pass.

Alternative method with salt brine

Some producers describe a cold method for formulations thickened with salt: dissolve the required salt in the smallest possible amount of water, stir this brine into the undiluted paste until it becomes more fluid, then add the remaining water. Others recommend dissolving the paste in hot water at around 80 °C with stirring before adding other ingredients. Follow the technical sheet for the specific grade, because methods are tested for particular products.

Rescuing a gelled batch

  • Stop adding water on top; it only thickens the gel skin.
  • Increase shear if the equipment allows, or recirculate through an in-line mixer.
  • Gently warm the batch within the supplier's recommended limits, which lowers viscosity.
  • Where practical, transfer the gel slowly into a fresh tank of moving water.
  • Avoid prolonged heating at high temperature or low pH, which can hydrolyse the ether sulphate.
Water in the tank first, paste in second, strong mixing throughout, and finish below about 28% active.

Supply considerations

Consistent paste makes dilution predictable. Ask for the active matter range, degree of ethoxylation and a certificate of analysis for each lot, and match the packing to your unloading equipment. For SLES supply questions, contact Nuroil through the contact page.

KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote