Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read5 sections

Knowledge centre · Industrial chemicals

Industrial nitric acid grades from 55% to 68% and their specifications

What separates 55%, 60%, 65% and 68% nitric acid, the parameters on a certificate of analysis, and how to choose the right strength for your use.

Written by the Nuroil trade desk, Sharjah

On this page · 5 sections
  1. 01Why the range stops at about 68%
  2. 02Common grades and typical uses
  3. 03Parameters on a certificate of analysis
  4. 04Choosing the strength
  5. 05Specifying an order

Industrial nitric acid is sold as a water solution at a stated strength, most commonly between 55% and 68% by weight. These are often called "weak" or "commercial" grades to distinguish them from concentrated and fuming acid above 90%, which is a separate product made by additional dehydration. This guide explains what the strengths mean and how to read a specification for them.

Why the range stops at about 68%

Nitric acid and water form an azeotrope at about 68% nitric acid, boiling at around 120 °C. At this point the vapour has the same composition as the liquid, so simple distillation cannot make it any stronger. Industrial plants produce acid in the 50 to 68% range directly from their absorption towers, and 68% is the strongest grade normally available without extra concentration steps.

Common grades and typical uses

Grade (by weight)Typical usersNotes
55 to 58%Fertilizer neutralisation and phosphate rock digestion, some chemical processesOften the direct output of medium-pressure plants; more water to evaporate downstream
60%Metal treatment, chemical intermediates, water and cleaning formulationsA common general industrial strength
65%Metal finishing, chemical synthesis, laboratory and analytical work (in higher purity forms)Widely traded strength; transport classification changes at 65%
68%Users wanting the highest commercial strength, metal treatment, chemical productionClose to the azeotrope; decomposes and fumes more readily than weaker acid

Parameters on a certificate of analysis

  • Nitric acid content (% w/w). Measured by titration with a standard alkali. Agreed tolerances are often expressed as a minimum or a narrow range.
  • Specific gravity or density. Rises with concentration; 68% acid has a density of about 1.41 g/cm³. Density is a useful cross-check on concentration in the field using a hydrometer and published tables.
  • Colour and appearance. Should be clear and colourless to pale yellow. Deeper colour indicates dissolved nitrogen oxides.
  • Dissolved nitrogen oxides (as NO₂ or as nitrous acid). A key quality parameter for metal finishing and chemical users.
  • Chloride. Important wherever the acid contacts stainless steel, because chloride promotes pitting.
  • Sulphate. Limited in some chemical and analytical applications.
  • Iron and heavy metals. Indicate corrosion in production or storage equipment; limited in higher grades.
  • Residue on ignition or evaporation. Non-volatile impurities left when the acid is evaporated.

Technical grades may report only concentration, colour and a few impurities. Higher-purity grades for electronics, analysis or pharmaceuticals report a much longer list of trace metals and anions to tighter limits.

Specify the concentration on a weight basis and confirm whether the figure is a minimum, a nominal value or a range.

Choosing the strength

01

Match your process

If your neutraliser, bath recipe or reactor is designed around a given strength, buy that strength rather than diluting or blending on site.
02

Consider dilution on site

If you need several strengths, buying the strongest and diluting can simplify stock. Dilution releases heat, and acid must always be added to water, in suitable equipment.
03

Weigh freight against handling

Stronger acid carries less water per tonne, but acid at 65% and above is more hazardous to handle and falls into a stricter transport category.
04

Check your sampling and testing

Concentration is usually checked on arrival by titration or density. Take samples with acid-resistant equipment into clean glass or fluoropolymer bottles, and test promptly, since dissolved nitrogen oxides can escape from an open sample and give a misleadingly low result for that parameter.

Specifying an order

State the concentration and tolerance, the impurity limits that matter to your process with their test methods, the packing and the quantity. Ask for a CoA with actual results. Nuroil provides a CoA with every delivery and can arrange CoO, SDS and third-party inspection on request. Send your specification through the quote request form.

KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote