Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Caustic soda & soda ash

Light soda ash specification: parameters and typical limits

A reference to the chemical and physical parameters on a light soda ash specification, with typical limits and the tests that sit behind them.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of light soda ash with detergent and water treatment
On this page · 6 sections
  1. 01How standards define the light grade
  2. 02Chemical parameters
  3. 03Physical parameters for the light grade
  4. 04Reading test results on a certificate
  5. 05Food and water treatment grades
  6. 06Writing your enquiry

A light soda ash specification has two halves. The chemical half, covering sodium carbonate content and impurities, is essentially the same as for dense ash because both are anhydrous sodium carbonate. The physical half, covering bulk density, particle size and sometimes absorptivity, is what defines the material as the light grade. This guide sets out the parameters you are likely to meet and what typical limits look like.

How standards define the light grade

National standards for technical soda ash usually describe light, medium and dense grades and separate them by bulk density. The chemical requirements are shared, with the bulk density band and sieve analysis changing from grade to grade. Producers' data sheets for light ash commonly quote a loose bulk density of roughly 0.5 to 0.7 kg per litre, against about 1 kg per litre or more for dense ash.

Chemical parameters

ParameterTypical technical-grade limitWhy it matters
Sodium carbonate (Na₂CO₃), dry basis99.2% minimumActive content; sets dosing and price per unit of alkali
Total alkalinity as Na₂OAbout 58% minimumAlternative way of expressing the same strength
Sodium chloride (NaCl)0.1% (1,000 ppm) maximum or lowerCorrosion and quality in glass, chemicals and textiles
Sodium sulphate (Na₂SO₄)0.2% maximum or lowerScaling and side reactions in some processes
Iron (Fe)About 20 ppm maximumColour in detergents, silicates and white products
Water-insoluble matter0.15% maximum or lowerSludge in dissolving tanks; residue on fabric
Loss on ignition / moistureCommonly well under 1%Shows moisture pick-up and partial hydration

Figures differ between producers and standards, and premium grades often run far below these limits. Treat the table as a guide to what to expect, and agree the actual limits in your contract.

Physical parameters for the light grade

  • Bulk density. The defining property. State whether you need loose (poured) or tapped density, as the numbers differ.
  • Particle size. Usually given as cumulative percentages retained on, or passing, a series of sieves. Light ash is fine; a large retained fraction on coarse sieves may indicate a different grade or caking.
  • Absorptivity. Important for detergent dry blending. Expressed as weight per cent of a test liquid held while the powder remains free-flowing. Not every producer reports it, so ask if you need it.
  • Appearance. White, free-flowing powder. Grey or yellow tints suggest contamination or high iron.

Reading test results on a certificate

A Certificate of Analysis should show the batch or lot number, the date of analysis, each parameter with its result and limit, and the test method. Sodium carbonate is usually found by titration with standard acid. Chloride, sulphate and iron use titration, gravimetric or colorimetric methods. Bulk density uses a standard cylinder or cup, and particle size a sieve shaker.

Compare results on a dry basis where the specification is written that way. A light ash that has absorbed moisture can show a slightly lower carbonate figure on an as-received basis without being chemically impure.

The chemistry tells you how pure the soda ash is; the physical tests tell you whether it is really the light grade your process was designed for.

Food and water treatment grades

Light soda ash also goes into food as additive E500 and into drinking water treatment. These uses bring extra limits, typically on heavy metals such as lead and arsenic, and require evidence of compliance with the relevant food additive or water-treatment standard. Do not assume a technical-grade certificate covers these uses.

Writing your enquiry

List the parameters that matter to your process, with limits, and say which test basis applies. Add bulk density and particle size if you need the light grade for a physical reason, and absorptivity if you dry-blend detergents. Nuroil provides a CoA with every delivery and can arrange independent laboratory testing at loading on request. Use the quote request form to send your specification.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote