Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read5 sections

Knowledge centre · Water & pool treatment

Keeping pool water balanced: free chlorine, pH and alkalinity

How free chlorine, pH and total alkalinity work together in a swimming pool, and which chemicals move each one up or down.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of soda ash production
On this page · 5 sections
  1. 01Free chlorine
  2. 02pH
  3. 03Total alkalinity
  4. 04How they work together
  5. 05Supplying a pool operation

Clear, safe pool water depends on a small number of measurements kept in the right relationship. Free chlorine does the disinfecting, pH decides how effective that chlorine is and how comfortable the water feels, and total alkalinity keeps pH from swinging. Get these three right, and most other problems become easier to manage.

Free chlorine

Free chlorine is the active disinfectant: the hypochlorous acid and hypochlorite ion left after chlorine has reacted with sweat, urine, cosmetics and other contaminants brought in by swimmers. When chlorine reacts with nitrogen compounds it forms combined chlorine, or chloramines, which disinfect poorly and cause the sharp smell and eye irritation often blamed on too much chlorine.

Operators test both free and total chlorine; the difference is combined chlorine. A rising combined chlorine figure signals that the pool needs more oxidation, better ventilation or more fresh water. Minimum free chlorine levels for public pools are set by local codes, and the maximum is set by the product label. Many codes treat free chlorine above about 10 ppm with bathers present as a reason to close the pool.

pH

pH controls how much of the free chlorine is in the strong hypochlorous acid form. At a higher pH, a greater share sits as the weaker hypochlorite ion, so the same chlorine reading disinfects less. pH that is too low makes water corrosive to metal fittings and plaster and uncomfortable for swimmers; pH that is too high encourages scale and cloudy water.

Health codes typically require pH within about 7.2 to 7.8, and many operators aim for the middle of that range. Tablet chlorine (TCCA) and dry acid push pH down; calcium hypochlorite and liquid hypochlorite push it up, and so does aeration from fountains and spray features, which drives off carbon dioxide.

Total alkalinity

Total alkalinity measures the water's buffering capacity, mostly bicarbonate. It is what stops pH from jumping every time a chemical is added. Too little alkalinity and pH drifts quickly; too much and pH tends to creep upwards and becomes hard to bring down.

Operators raise alkalinity with sodium bicarbonate, which has little effect on pH. Soda ash (sodium carbonate) raises both pH and alkalinity, making it the usual choice when both are low. Alkalinity is lowered with acid, either dry acid (sodium bisulphate) or hydrochloric acid, often combined with aeration to lift pH back without restoring alkalinity.

To changeRaise withLower with
Free chlorineCalcium hypochlorite, TCCA, sodium hypochlorite, sodium dichlorStop dosing and allow it to fall; sodium thiosulphate in larger corrections
pHSoda ash; aerationSodium bisulphate (dry acid); hydrochloric acid
Total alkalinitySodium bicarbonate; soda ashSodium bisulphate or hydrochloric acid
Calcium hardnessCalcium chloride; calcium hypochlorite adds a littlePartial drain and refill

How they work together

The usual order of work is alkalinity first, then pH, then chlorine. Correcting alkalinity stabilises pH; correcting pH makes chlorine readings meaningful. Calcium hardness and water temperature complete the picture, because together with pH and alkalinity they decide whether water tends to dissolve or deposit calcium carbonate. Operators use saturation index calculations to check this balance.

Outdoor pools add one more factor: cyanuric acid, the stabiliser that protects chlorine from sunlight but also slows its action. That is covered in our article on stabilised and unstabilised chlorine.

  • Test at regular intervals set by your local code, and record the results.
  • Add chemicals with the circulation running, in the amounts the label gives, and retest after mixing.
  • Add chemicals separately into the pool water, never mixed with each other in a bucket or feeder.
Balance alkalinity first, then pH, then chlorine. A correct pH is what makes a chlorine reading count.

Supplying a pool operation

A balanced chemical programme needs a reliable supply of a chlorine source, a pH reducer and a pH or alkalinity raiser. When enquiring, list each chemical with its form and minimum assay, the pack size your plant room can handle and the monthly volume. Nuroil supplies soda ash and, on request, pool chlorine compounds and sodium bisulphate; the swimming pool page lists what is available.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote