Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read5 sections

Knowledge centre · Industrial chemicals

Industrial uses of nitric and phosphoric acid

How nitric and phosphoric acid are made, their main uses in fertilizer production and metal treatment, commercial grades and handling basics.

Written by the Nuroil trade desk, Sharjah

On this page · 5 sections
  1. 01Nitric acid
  2. 02Phosphoric acid
  3. 03Side-by-side comparison
  4. 04Handling basics
  5. 05Buying and documentation

Nitric acid and phosphoric acid are two of the most important mineral acids in industry. Both are central to fertilizer production, and both are used to treat metal surfaces, but they behave very differently. This article covers how they are made, what they are used for and what buyers should know about grades and handling.

Nitric acid

Nitric acid is made by the Ostwald process. Ammonia is burned over a catalyst to form nitric oxide, which is oxidised to nitrogen dioxide and then absorbed in water to form the acid. Commercial solutions are typically 52 to 68% nitric acid by mass. Around 68% the acid forms an azeotrope with water, so stronger "fuming" grades above about 86% require extra dehydration steps.

01

Fertilizer

By far the largest use is reacting nitric acid with ammonia to make ammonium nitrate, which is used in straight nitrogen fertilizers and in products such as calcium ammonium nitrate and urea ammonium nitrate solutions.
02

Chemical intermediates

Nitric acid is used to make adipic acid, a building block for nylon, and to nitrate aromatic compounds such as benzene, the first step towards aniline and the polyurethane chain.
03

Metal treatment

Diluted nitric acid is widely used to passivate stainless steel. It dissolves free iron from the surface and helps form a chromium-rich passive film that resists corrosion. It is also used, often blended with other acids, for pickling stainless steel, etching and bright dipping, and cleaning in electronics manufacturing.

Phosphoric acid

Most phosphoric acid is produced by the wet process: phosphate rock is digested with sulphuric acid, giving a dilute phosphoric acid and gypsum as a by-product. The acid is then concentrated. A thermal route, in which elemental phosphorus is burned and the oxide absorbed in water, gives a purer acid at higher cost and is used for food and high-purity grades. Merchant-grade acid is usually sold as around 75 to 85% phosphoric acid, roughly 54 to 62% P₂O₅.

01

Fertilizer

Fertilizer production consumes the large majority of phosphoric acid. Reacting it with ammonia gives the ammonium phosphates, monoammonium and diammonium phosphate, and it is also used to make triple superphosphate and liquid fertilizers.
02

Metal treatment

Phosphoric acid is the basis of phosphate conversion coatings. Steel parts are treated to form a thin crystalline phosphate layer that improves paint adhesion and corrosion resistance, a step widely used before painting vehicle bodies, appliances and fabricated steel. It is also used in rust converters, metal cleaners and descalers.
03

Other uses

Purified grades serve as acidulants in food and beverages, pH adjusters, sanitisers in dairy and brewing plants and in water treatment.

Side-by-side comparison

FeatureNitric acidPhosphoric acid
Main production routeOxidation of ammonia (Ostwald process)Phosphate rock with sulphuric acid (wet process)
Typical commercial strength52–68% HNO₃75–85% H₃PO₄
Largest useAmmonium nitrate fertilizersAmmonium phosphate fertilizers
Metal treatment rolePassivation, pickling and etchingPhosphating, rust conversion, cleaning
Key hazardCorrosive and a strong oxidiser; gives off toxic nitrogen dioxideCorrosive; causes severe skin burns and eye damage

Handling basics

Both acids are corrosive and must be handled with chemical goggles, face shield, acid-resistant gloves and protective clothing, with eyewash and safety showers nearby. Nitric acid needs extra care because it is a powerful oxidising agent: it can react violently with organic materials, reducing agents, many metals and combustibles, and it releases toxic nitrogen dioxide fumes when it decomposes. Store it apart from organic chemicals, alkalis and flammables, in containers of a material the SDS confirms as compatible. Phosphoric acid is less reactive but still causes serious burns, and it attacks many metals. Always consult the product safety data sheet for storage materials, segregation and first aid.

Same end markets, different chemistry: treat phosphoric acid as a strong corrosive, and nitric acid as a corrosive that is also a strong oxidiser.

Buying and documentation

Specify the concentration, the grade (technical, merchant, food or electronic), key impurity limits such as iron, chloride, sulphate or heavy metals, and the packing: drums, IBCs or bulk. Both acids are dangerous goods, so check that the packaging and transport documents match. Ask for a certificate of analysis for each batch and the SDS. Nuroil supplies industrial and specialty chemicals to manufacturers and distributors, with CoA on every delivery and third-party inspection on request; send your specification through the quote request form.

KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote