Ethyl acetate is one of the most common industrial solvents. It is the fast-drying, fruity-smelling liquid behind many lacquers, flexible packaging inks and solvent-based adhesives. This article covers what it is, why formulators choose it and what to watch when buying and storing it.
What ethyl acetate is
Ethyl acetate is an ester, made mainly by reacting ethanol with acetic acid in the presence of an acid catalyst, with water removed to push the reaction to completion. Other industrial routes start from acetaldehyde or from ethylene and acetic acid. The product is a clear, colourless liquid with a sweet, ester-like odour.
| Property | Typical value | Why it matters |
|---|---|---|
| Boiling point | About 77 °C | Evaporates quickly, so coatings and inks dry fast |
| Flash point | About minus 4 °C | Highly flammable at normal temperatures |
| Explosive limits in air | About 2 to 11.5% | Ventilation and ignition control are essential |
| Density | About 0.90 g/cm³ | Lighter than water |
| Solubility in water | About 8 g per 100 mL at 20 °C | Partly soluble; miscible with most organic solvents |
Why formulators like it
- Strong solvency. It dissolves a wide range of resins, including nitrocellulose, acrylics, vinyls, polyurethanes and many epoxies.
- Fast, clean evaporation. Its low boiling point lets films dry quickly, and it leaves little residual odour when properly dried.
- Easy blending. It mixes with alcohols, ketones and hydrocarbons, so it can be combined with slower solvents to tune drying speed.
- Relatively low toxicity. Compared with many solvents it has low acute toxicity, although vapour still irritates eyes and airways and high exposure causes drowsiness.
Coatings
In coatings, ethyl acetate is used in nitrocellulose and acrylic lacquers, wood finishes, can and closure coatings, automotive refinish systems and many two-component paints. It is often part of a solvent blend: the fast ester gives quick surface drying, while slower solvents keep the film open long enough to level without blushing or orange peel. In two-component polyurethane systems it also serves as a diluent for the hardener, which is why a low-water, low-alcohol grade matters there: both water and alcohols react with isocyanates and can spoil the cure.
Printing inks
Gravure and flexographic inks for flexible packaging rely heavily on ethyl acetate, often blended with alcohols. High-speed presses need ink that dries in the fraction of a second between print stations and before the web is rewound. Low retained solvent in the finished film matters for food packaging, so printers monitor drying closely and choose grades with consistent purity.
Adhesives
Solvent-based contact adhesives, laminating adhesives and some pressure-sensitive adhesives use ethyl acetate to dissolve the polymer and then flash off quickly once applied. Its evaporation rate gives a workable open time without very long drying, and its solvency suits polyurethane and acrylic adhesive systems. It is also used in cleaning equipment and in consumer products such as nail polish remover.
Storage and handling
Ethyl acetate is classified as a highly flammable liquid that causes serious eye irritation and may cause drowsiness or dizziness. Store it in closed containers in a cool, well-ventilated area away from heat, sparks and oxidisers. Earth and bond containers during transfer to prevent static discharge, use explosion-protected equipment where vapour may be present, and keep workplace exposure below local limits. In the presence of water it slowly hydrolyses back to ethanol and acetic acid, so containers should be kept sealed to protect quality. Refer to the supplier's safety data sheet for full guidance.
Ethyl acetate's value is fast, predictable evaporation, and the same property is why it must be stored and handled as a highly flammable liquid.
What to specify when buying
Common commercial grades are 99.5% minimum purity, with limits on water, acidity (as acetic acid), residual ethanol, colour and non-volatile residue. For polyurethane work, specify a urethane grade with tight water and alcohol limits. State packing (steel drums, IBCs or ISO tanks) and remember it ships as a dangerous good. Ask for a batch certificate of analysis and the SDS. Nuroil supplies industrial and specialty chemicals with CoA on every delivery; set out your specification on the quote request form.
