Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read5 sections

Knowledge centre · Urea & fertilizers

Foliar urea sprays and why biuret content matters

Urea is the most common foliar nitrogen source. Why low-biuret grades are needed for repeated sprays, and how to avoid leaf burn.

Written by the Nuroil trade desk, Sharjah

Illustration of Nuroil urea bag and granules in a crop field
On this page · 5 sections
  1. 01What biuret is
  2. 02How much is too much?
  3. 03Getting the spray right
  4. 04Foliar nitrogen is a supplement
  5. 05Specifying urea for foliar programmes

Spraying nitrogen onto leaves is a useful supplement to soil fertilizer in orchards, vineyards and some field crops. It can correct a deficiency quickly, deliver nitrogen when roots are inactive, or support flowering and fruit set. Urea is usually the first choice for foliar nitrogen because it is highly soluble, has a low salt index and is taken up rapidly by leaves. But not all urea is equally suited to the sprayer, and the difference comes down to one impurity: biuret.

What biuret is

Biuret forms when two urea molecules combine at high temperature, releasing ammonia. A small amount is created in every urea plant during evaporation and finishing, so all commercial urea contains some. In soil, biuret is broken down by microbes into plant-available nitrogen, and at the levels found in normal fertilizer-grade urea it is not a practical concern for soil application.

On leaves it is different. Plants do not readily metabolise biuret, so it accumulates in leaf tissue, particularly at leaf tips and margins. At high enough concentrations it causes yellowing and tip burn and can disturb growth. In long-lived evergreen crops such as citrus, biuret from repeated sprays can build up over seasons.

How much is too much?

Advice varies between crops and advisory bodies, but the direction is consistent:

  • Citrus extension guidance in Florida recommends that urea for foliar sprays contain no more than about 0.2 percent biuret.
  • Australian fertilizer guidance describes standard urea as unsuitable for repeated foliar use on perennial horticultural crops, and recommends low-biuret grades where high rates are sprayed or crops are sprayed every year.
  • A single spray of standard urea is often tolerated by annual crops, and urea used at low rates as a tank-mix adjuvant with trace elements is treated differently from urea used as a main nitrogen source.
UseBiuret consideration
Soil application, broadcast or bandedStandard agricultural grade is suitable
FertigationStandard grade generally suitable; check with crop adviser for sensitive crops
Occasional foliar spray on annual cropsStandard grade often tolerated at moderate concentration
Repeated foliar sprays on citrus and other perennialsLow-biuret grade recommended

Getting the spray right

Even low-biuret urea can scorch leaves if the spray is too concentrated or applied in the wrong conditions. Points that reduce the risk:

  • Concentration. Follow crop-specific guidance. Higher spray volumes are not always safer: in citrus, very high volumes have been linked to more tip burn because spray pools at leaf tips.
  • Timing of day. Leaves absorb urea most effectively while spray droplets stay wet. Studies show better uptake from early-morning sprays in humid conditions than from midday sprays in hot, dry weather, although very cold conditions also slow absorption.
  • Speed of uptake. Much of the applied urea enters the leaf within hours, with uptake continuing for a day or two in favourable humidity.
  • Tank mixes. Mixed sprays should not be too concentrated, and a small jar or bucket compatibility test before mixing a full tank is good practice.
  • Water quality. Clean water avoids nozzle blockage and unwanted reactions with other products in the tank.

Foliar nitrogen is a supplement

Leaves can only take up a limited amount of nitrogen per spray before scorch becomes a risk. Foliar urea suits targeted, timely doses; it does not replace a soil nitrogen programme for most crops.

Specifying urea for foliar programmes

Biuret should appear on every certificate of analysis for urea. If the product is destined for foliar use, state a maximum biuret figure in your enquiry rather than relying on a general agricultural specification, and ask for results per lot. Other useful requirements include low insolubles, so the product dissolves cleanly, and free-flowing prills or granules. Nuroil can quote agriculture-grade urea against your biuret limit and supplies a CoA with each delivery; send details through the quote form.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote