Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read5 sections

Knowledge centre · Industrial chemicals

How fast ethyl acetate evaporates compared with other solvents

What the relative evaporation rate scale means, where ethyl acetate sits against acetone, MEK, toluene and butyl acetate, and why it matters.

Written by the Nuroil trade desk, Sharjah

On this page · 5 sections
  1. 01The relative evaporation rate scale
  2. 02Where ethyl acetate sits
  3. 03Why the number matters in practice
  4. 04Faster evaporation, higher vapour load
  5. 05Buying for consistent drying

Ethyl acetate is chosen in many formulations precisely because it leaves quickly. Printing inks dry between stations, adhesives become tacky in seconds and lacquers set before dust can land. But "fast" is relative, and formulators usually describe solvent speed with a number on a comparison scale. Understanding that scale helps when you replace one solvent with another or blend them.

The relative evaporation rate scale

Solvent data sheets usually quote evaporation rate relative to n-butyl acetate, which is given the value 1.0. A solvent rated 4 evaporates roughly four times as fast as n-butyl acetate under the same test conditions; one rated 0.5 takes about twice as long.

These figures come from laboratory tests on a thin film of solvent under controlled air flow and temperature. The ASTM method traditionally used for this has been withdrawn, and published values for the same solvent differ between data sources. Treat the numbers as a ranking tool, not a precise prediction of how long a film will take to dry on your line.

Where ethyl acetate sits

Ethyl acetate is commonly listed at about 4.1 on the n-butyl acetate scale, placing it among the fast solvents. Typical published values for common alternatives are shown below.

SolventApproximate relative evaporation rate (n-butyl acetate = 1)Closed-cup flash point
Acetoneabout 5.6 to 6.3about −20 °C
Ethyl acetateabout 4.1about −4 °C
Methyl ethyl ketone (MEK)about 3.8below 0 °C
Tolueneabout 1.9about 4 °C
Isopropyl alcoholabout 1.7about 12 °C
n-Butyl acetate1.0 (reference)about 22 °C
Xylenesabout 0.6 to 0.7about 25 to 30 °C

Values vary by source and test conditions; check the supplier data sheet for the material you buy.

Why the number matters in practice

01

Too fast can be as bad as too slow

When a very fast solvent flashes off, it cools the surface. In humid conditions moisture can condense into the wet film, causing white haze or "blushing" in lacquers. Fast evaporation can also trap air, leave orange-peel texture or dry ink on the printing plate before it transfers.
02

Blends are tuned with slower solvents

Many ink and coating systems pair ethyl acetate with a slower solvent such as n-butyl acetate or a glycol ether so that the film levels before it sets. Swapping in a different fast solvent changes that balance.
03

Ethyl acetate and MEK are close, acetone is faster

On speed alone ethyl acetate sits between MEK and acetone. Solvency, odour, regulatory status and cost then decide the choice. Ethyl acetate is often preferred where a milder odour and a favourable toxicity profile matter, for example in food packaging inks.
04

Climate changes the picture

The same blend dries faster on a hot line in summer than in a cool, air-conditioned hall. Plants in warm regions sometimes shift the ratio of fast to slow solvent seasonally, and any change of solvent supplier is best checked with a drawdown or a short press trial before full production.

Faster evaporation, higher vapour load

A fast solvent puts more vapour into the air in a given time. Ethyl acetate has a closed-cup flash point of around −4 °C, which means flammable vapour forms at any normal ambient temperature, and its vapour is heavier than air. Drying tunnels, extraction and ventilation must be sized for the solvent actually used. If you change from a slower solvent, review the explosion protection and exposure assessment, as well as the drying profile.

Buying for consistent drying

Evaporation behaviour depends on purity. Residual ethanol, water and heavier impurities change how a blend dries, so a consistent specification from batch to batch keeps line settings stable. When enquiring, state the grade (for example 99.5% minimum), the maximum water and alcohol content you need and the packing you prefer. Nuroil provides a CoA with each delivery and the SDS on request; use the quote request form to send your specification.

KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote