Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read6 sections

Knowledge centre · Caustic soda & soda ash

Dissolving light soda ash for dosing solutions

How to make up light soda ash solutions without lumps, crusts or dust: water temperature, solubility, mixing order and practical solution strengths.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of light soda ash with detergent and water treatment
On this page · 6 sections
  1. 01Solubility depends strongly on temperature
  2. 02Why lumps and crusts form
  3. 03A sensible make-up routine
  4. 04Safety basics
  5. 05Water treatment grades and documents
  6. 06What to specify when buying

Water treatment plants, textile dye houses and chemical plants often dose soda ash as a solution rather than as a powder. Light soda ash is popular for this because its fine particles dissolve quickly. It still behaves in ways that catch operators out: lumps that refuse to dissolve, hard crusts on tank walls and a cloud of fine dust at the bag-tipping point. Most of these problems come from the chemistry of sodium carbonate and water.

Solubility depends strongly on temperature

Sodium carbonate is unusual. Its solubility rises steeply as water warms from freezing to about 35 °C and then falls slightly as the water gets hotter. Reference data give roughly 7 g per 100 mL of water at 0 °C, rising to nearly 49 g per 100 mL at about 35 °C and easing to around 44 g at 100 °C.

Two practical points follow. A solution made up near its limit on a warm afternoon can crystallise in pipework and dosing pumps on a cold night. And a strong solution stored outdoors in winter may drop solids in the tank. Most plants therefore make up solutions well below saturation, often in the 10 to 20 per cent range, and size dosing pumps accordingly. Your process designer should confirm the strength that suits your lowest expected temperature.

Why lumps and crusts form

Anhydrous sodium carbonate combines with water to form hydrates. Below about 32 °C the stable crystal is the decahydrate; above about 35 °C it is the monohydrate. When dry powder meets a small amount of water, the wetted outer layer can hydrate and set into a hard shell around dry powder inside. The result is a lump that dissolves slowly and can block suction strainers.

The same reaction gives off heat. Dissolving anhydrous soda ash warms the solution, which is one reason operators should treat fresh mixes with care.

A sensible make-up routine

  1. Fill the tank with most of the required water first, and start the agitator.
  2. Add the light ash steadily onto the moving water surface, not as one heap. A bag-tipping station with a screen and local dust extraction helps.
  3. Avoid adding water onto a pile of dry powder in an empty tank.
  4. Keep agitating until the solution is clear, then top up to volume and check strength with a density reading or titration.
  5. Rinse splashes off tank walls and lids so that crusts do not build up.
ProblemLikely causeFix
Lumps at the tank bottomPowder added too fast, or water added onto powderAdd powder to moving water; slow the feed
Crystals in lines overnightSolution too strong for the lowest temperatureReduce strength or insulate and trace lines
Hard crust on wallsSplashes drying and hydratingRinse regularly; fit splash guards
Dust at the tipping pointFine light ash released from bagsLocal extraction, slower tipping, dust masks

Safety basics

Soda ash is a strong alkali in solution. Dust and solution irritate eyes, skin and the respiratory tract, and eye contact can be serious. Operators should wear chemical splash goggles, gloves and suitable dust protection when tipping bags. Keep an eyewash station near the make-up area. The product SDS gives the full precautions and first-aid measures for the specific material you receive.

Add light soda ash to moving water, never water to a heap of ash, and size the solution for the coldest night rather than the warmest day.

Water treatment grades and documents

For drinking water, many utilities require soda ash that complies with a recognised water-treatment standard, such as AWWA B201 or a national equivalent, and will ask for the certificate. Industrial users generally need a Certificate of Analysis showing sodium carbonate content and insoluble matter, because insolubles settle as sludge in dosing tanks.

What to specify when buying

State that you need the light grade, your sodium carbonate minimum and the maximum insoluble matter. If the product is for potable water, name the standard it must meet. Nuroil supplies light soda ash in bags or bulk bags with a CoA on each delivery; MSDS and third-party inspection are available on request. Contact us through the contact page to discuss your dosing system.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote