Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read6 sections

Knowledge centre · Caustic soda & soda ash

Dry feeding caustic soda pearls with screw feeders and hoppers

How to dose caustic soda pearls dry: feeder types, hopper design, keeping air dry, materials of construction and the safety points to cover.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of caustic soda pearls in a glass dish
On this page · 6 sections
  1. 01Why pearls suit dry feeding
  2. 02Feeder types
  3. 03Hopper and feeder design points
  4. 04Materials of construction
  5. 05Safety around dry feeders
  6. 06Specifying pearls for a dry feed

Most caustic soda is dosed as a solution. But some plants feed the solid directly, either into a dissolving tank at a controlled rate or into a dry blend. For these systems pearls are the preferred form, because their round, uniform particles flow far more predictably than flakes. This article covers the main equipment choices and the conditions that keep a dry caustic feed working.

Why pearls suit dry feeding

Pearls are spheres of roughly even size, usually below about 1 mm. They pour like fine gravel, fill feeder screws consistently and are much less prone to bridging than flat, irregular flakes. Producers note that the particle size of beads is close to that of granular soda ash, silicates and phosphates, which helps blends stay uniform. The weak point is moisture: caustic is strongly hygroscopic, and a pearl that has picked up water becomes sticky, then cements to its neighbours.

Feeder types

FeederHow it dosesSuits
Volumetric screw feederA helical screw delivers a set volume per revolution; rate set by speedSteady feed to a dissolving tank where small rate errors are acceptable
Loss-in-weight feederHopper sits on load cells; controller adjusts screw speed to hit a mass rateBlending and processes needing accurate mass dosing
Batch weigh hopperWeighs a charge, then discharges it in one goBatch make-up of solutions or dry mixes
Rotary valveRotating pockets meter product from a siloDischarge from bulk silos into pneumatic lines or screws

Volumetric feeders are simple and robust; suppliers quote accuracies of around 2% for free-flowing materials, but accuracy depends on consistent bulk density, which moisture pickup quickly upsets. Loss-in-weight control compensates by measuring what has actually left the hopper.

Hopper and feeder design points

  • Keep the hopper sealed and dry. Use a tight lid, a desiccant breather or a small purge of dry air or nitrogen. Bulk handling of beads relies on very dry air; one producer specifies air at a dew point of about −40 °C during pneumatic unloading.
  • Avoid moist air from the dissolving tank. Warm, humid vapour rising from the tank into the feeder outlet is the most common cause of build-up. Use a drop chute, a vapour barrier or a small air sweep at the discharge.
  • Conditioning. A slow agitator or overwind helix inside the hopper keeps product moving and breaks any weak bridges.
  • Hopper size. Size for a short residence time, ideally a shift or less, so that product does not sit exposed for days.
  • Dust control. Pearls are largely dust-free, but abrasion in conveying makes some fines. Fit a dust collector on bag tipping stations and on pneumatic receivers.

Materials of construction

Dry caustic is handled in carbon or stainless steel feeders; many water treatment units use all-stainless construction for the hopper, screw and trough. Avoid aluminium, zinc, galvanised parts and brass, because damp caustic attacks them and can release hydrogen. Check seals and flexible connectors for alkali resistance.

Safety around dry feeders

  • Bag tipping stations should have a grid to stop bags falling in, a dust hood and a platform at a safe working height.
  • Operators need goggles with a face shield, alkali-resistant gloves and protective clothing, and a safety shower and eyewash within easy reach.
  • Isolate and lock out before clearing a blocked screw; never reach into a hopper by hand.
  • Clean up spilled pearls promptly. They roll underfoot and turn into a corrosive paste when damp.
Pearls make dry feeding practical, but only if the hopper, the feeder outlet and the surrounding air are kept dry.

Specifying pearls for a dry feed

Give your supplier the feeder type and the particle size range it was designed for, and ask for the size distribution on the certificate of analysis. Bulk bags with inner liners and a discharge spout suit hopper filling; 25 kg bags suit manual tipping. Nuroil supplies caustic soda pearls in both formats; contact us to discuss packing for your system.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote