Nitric acid, HNO₃, is a strong mineral acid and a strong oxidiser. The commercial product is a solution in water, usually 55% to 68%; at about 68% it forms an azeotrope with water, so this is the strongest grade made by ordinary absorption.
It is clear when fresh and turns pale yellow as dissolved nitrogen dioxide builds up with light and heat. It attacks most metals and organic materials, so it is stored in stainless steel or rated plastics and kept apart from fuels, alkalis and other acids.
Identity
Formula
HNO₃
Molar mass
63.01 g/mol
CAS
7697-37-2
Nitric acid · HNO₃Why Nitric acid
Strength to suit the process55%, 60%, 65% or 68% HNO₃, so you pay for the acid you need and not for water you will add back.
Acid and oxidiser in oneSupplies nitrate and oxidising power for fertilizers, pickling, etching and nitration.
Bulk or packedISO tanks for plants with storage; drums and IBCs for smaller users.
Documented qualityEach offered batch comes with its Certificate of Analysis and safety data sheet.
What Nuroil does on every order
Why choose nitric acid from Nuroil?
Checked against the batch CoA
HNO₃ content, nitrous acid and residue are reviewed on the batch certificate before loading.
Dangerous-goods paperwork handled
Shipped as class 8 under UN 2031, with the oxidiser subsidiary risk from 65%, and the correct labels and declarations.
Packed in rated containers
Drums, IBCs and tanks approved for nitric acid at the offered strength.
One desk, firm offers
FOB, CFR or CIF from our Sharjah trade desk, usually within 24 hours.
02 TECHNICAL DATA
Technical specification.
HNO₃ content
55%, 60%, 65% or 68% min, by gradeAcid-base titration
Density at 20 °C
About 1.34 (55%) to 1.41 (68%) g/cm³Hydrometer / densimeter
Nitrous acid (as HNO₂)
0.1–0.2% maxPermanganate titration
Residue on ignition
0.02% maxGravimetric
Iron (Fe)
Low ppm; specified on high-purity gradesICP / colorimetric
Appearance
Clear, colourless to pale yellow liquidVisual
Odour
Sharp, acrid
0155–60% HNO₃
Fertilizer and general use
The usual strength for ammonium nitrate and nitrophosphate fertilizers, and for dilution in metal treatment and cleaning.
0265–68% HNO₃
Highest commercial strength
The azeotropic acid for pickling, etching, passivation and chemical synthesis, and where freight per unit of acid matters.
Selection guidance Tell us the process, the strength you dose at and any purity limits, and we will confirm the grade and packing.
The same acid at two strengths. The right one depends on your process and freight.
Property
55–60% HNO₃
65–68% HNO₃
Density at 20 °C
About 1.34–1.37 g/cm³
About 1.39–1.41 g/cm³
Acid per tonne shipped
Lower
Higher
Fuming
Some
More
Transport class
Class 8, PG II
Class 8 with 5.1 subsidiary, PG II
Best suited to
Fertilizers, dilution, cleaning
Pickling, etching, synthesis, long freight
03 HOW IT IS MADE
From ammonia and air to nitric acid.
Nitric acid is made by the Ostwald process. Ammonia is burned with air over a platinum-rhodium gauze to nitric oxide, which is oxidised further to nitrogen dioxide and absorbed in water to give acid of up to about 68%.
01
Ammonia and air
Vaporised ammonia is mixed with filtered, compressed air.
02
Catalytic oxidation
The mixture burns over a platinum-rhodium gauze to nitric oxide.
03
Absorption
Nitric oxide is oxidised to nitrogen dioxide and absorbed in water in towers.
04
Bleaching and testing
Dissolved gases are stripped, and each batch is tested for strength before loading.
04 APPLICATIONS
Where it is used.
01
Fertilizers
Ammonium nitrate, calcium ammonium nitrate and nitrophosphate production.
02
Explosives
Nitration for ammonium nitrate explosives, nitroglycerine and nitrocellulose.
03
Metal treatment
Pickling, passivation of stainless steel, etching and brightening.
04
Chemical synthesis
Nitration of organics for dyes, pharmaceuticals and intermediates such as adipic acid.
05
Electronics and plating
Cleaning and etching of metal surfaces and circuit boards.
06
Industrial cleaning
Descaling and cleaning of plant, often with other acids.
05 SAFETY & HANDLING
Corrosive and oxidising. Handle with care.
This summary does not replace the Safety Data Sheet. Review the SDS and site procedure before first handling.
Danger
H272 May intensify fire; oxidiser (65% and above).
H290 May be corrosive to metals.
H314 Causes severe skin burns and eye damage.
H331 Toxic if inhaled.
EUH071 Corrosive to the respiratory tract.
UN
2031
Class
8 (5.1 from 65%) · PG II
01
Full protection
It causes severe burns; wear acid-resistant gloves, face shield, goggles and protective clothing.
02
Do not breathe the fumes
The fumes and nitrogen oxides are toxic and corrosive to the airways; work with ventilation or extraction.
03
Away from fuels and organics
As an oxidiser it can ignite wood, paper, oils and solvents; keep it apart from them.
04
Add acid to water
When diluting, add the acid slowly to water, never water to the acid.
05
Exposure response
Rinse skin or eyes immediately with plenty of water for at least 15 minutes and seek medical attention.
Cool, shaded and segregated.
StoreCool, shaded, apart
Light and heat slowly decompose the acid to nitrogen dioxide, which turns it yellow and builds pressure in closed containers. Kept cool, shaded and sealed it holds its strength. Confirm the producer’s shelf life with the offer.
Rated containers onlyStainless steel or plastics approved for nitric acid at the stored strength.
Cool, ventilated storeOut of direct sun, with ventilation and acid-resistant bunding.
SegregateApart from alkalis, metals, fuels, organics and other acids.
First in, first outUse the oldest stock first and keep the batch label with each lot.
Plan documentation early.
HS code2808.00
CAS number7697-37-2
EC number231-714-2
UN numberUN 2031
GHS
Oxidising liquid (from 65%); skin corrosion 1A; toxic if inhaled; corrosive to metals
Transport
UN 2031, class 8, PG II; from 65% to 70% with subsidiary class 5.1
Precursor controls
Some countries license nitric acid as an explosives precursor: confirm before ordering
National regulations
Confirm the destination’s import and dangerous-goods requirements
06 PACKING OPTIONS
Choose your packing.
Container types, sizes and loads depend on the producer and strength; the offer confirms them.
Small quantities
Drums
UN-approved drums rated for nitric acid, for plants and distributors.
Nitric acid and water form an azeotrope at about 68% HNO₃, so ordinary absorption and distillation stop there. Stronger, fuming acid needs a separate concentration process.
02Why does nitric acid turn yellow?
Light and heat decompose a little of the acid to nitrogen dioxide, which dissolves and colours it. Store it cool, shaded and sealed to keep this to a minimum.
03Which grade should I choose?
55–60% suits fertilizer production and processes that dilute the acid. 65–68% carries more acid per tonne and suits pickling, etching and synthesis.
04Is it dangerous goods for shipping?
Yes. It ships as UN 2031, class 8, packing group II; from 65% to 70% HNO₃ it also carries the class 5.1 oxidiser subsidiary risk. We prepare the dangerous-goods documents with the shipment.
05What is the HS code?
Nitric acid is classified under HS 2808.00. Its CAS number is 7697-37-2.
06What containers can hold it?
Stainless steel, and plastics approved for nitric acid at that strength. It attacks carbon steel, copper and most rubbers.
07What documents come with a shipment?
A Certificate of Analysis and Safety Data Sheet, with the Certificate of Origin, dangerous-goods declaration and any end-use statement the destination requires.
Include the strength, use, packing, quantity and destination for a tailored offer. We reply with a firm FOB, CFR or CIF offer, usually within 24 hours.