Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
NUROIL / FUEL OIL / DMX

DMX.Light distillate.

The lightest ISO 8217 marine distillate, with the lowest viscosity and flash point of the DM grades.

  • Viscosity at 40°C 1.4 – 5.5 cSt
  • Cetane index min. 45
  • Sulphur max. 1.0 mass %
  • Flash point min. 43 °C
  • ISO 8217
Pencil sketch of a petroleum laboratory bench with fuel oil samples, a hydrometer, a flash point tester and a certificate of analysis
ISO 8217 categoryDMXSulphur max. 1.0 mass %
DMX1.4 – 5.5 cStEmergency and lifeboat distillate
HazardDangerUN UN 1202, gas oil · per SDS
CategoryISO 8217 DMX
FamilyMarine distillate
Viscosity at 40°C1.4 – 5.5 cSt
Cetane indexmin. 45
Sulphurmax. 1.0 mass %
Switch gradeBunker and marine fuel
Compare the marine grades
01 THE GRADE

What is DMX?

The lightest ISO 8217 marine distillate, with the lowest viscosity and flash point of the DM grades. It is used where a low-temperature, clean distillate is required, such as emergency equipment and lifeboat engines.

Grades that start DM are distillates, from the light DMX to the heavier DMB. They are clear fuels with low viscosity and are measured at 40°C.

Identity
ISO 8217 category
DMX
Viscosity
1.4 – 5.5 cSt at 40°C
Sulphur
max. 1.0 mass %
Marine distillate · ISO 8217 DMX
Why DMX marine fuel
  • Emergency or cold-start equipmentLowest viscosity and flash point of the distillates, with a cloud-point limit.
  • Supplied to your ISO 8217 specificationTell us the grade, sulphur limit and engine requirement. We quote against that specification, not a generic product.
  • Every batch verifiedEach delivery is tested against the agreed grade and reported on a Certificate of Analysis. Independent inspection can be arranged.
  • Bunker-ready supplyRoad tanker, barge and ship-to-ship delivery from Gulf ports, arranged around the vessel’s schedule.
What Nuroil does on every order

Why source DMX from Nuroil?

  • Every batch, verified

    Certificate of Analysis with every shipment, confirming viscosity, sulphur, density and flash point against the grade ordered.

  • Supplied to your specification

    Agree the grade, standard edition and required parameters before confirming your order.

  • Bunker-ready supply

    Vessel delivery at UAE ports and anchorages, or tanker and drum supply to industrial sites, matched to your schedule.

  • One desk, firm offers

    Share the grade, quantity, delivery method and location. Our team replies with the offer within 24 hours.

02 TECHNICAL DATA

Catalogue specification.

Viscosity at 40°C, max
5.5 mm²/s (cSt)ASTM D445 / ISO 3104
Viscosity at 40°C, min
1.4 mm²/s (cSt)ASTM D445 / ISO 3104
Density at 15°C, max
Not specifiedASTM D1298 / ISO 3675
Cetane index, min
45ASTM D4737 / ISO 4264
Sulphur, max
1.0 mass %ASTM D4294 / ISO 8754
Flash point, min
43 °CASTM D93 / ISO 2719
Hydrogen sulphide, max
2.0 mg/kgIP 570
Acid number, max
0.5 mg KOH/gASTM D664
Total sediment by hot filtration, max
Not specifiedISO 10307-1
Show all 18 propertiesShow fewer
Oxidation stability, max
25 g/m³ISO 12205
Carbon residue (micro), max
0.30 mass %ASTM D4530 / ISO 10370
Cloud point, max
-16 °CISO 3015
Pour point (winter), max
Not specifiedASTM D97 / ISO 3016
Pour point (summer), max
Not specifiedASTM D97 / ISO 3016
Appearance
Clear and brightVisual
Water, max
Not specifiedASTM D95 / ISO 3733
Ash, max
0.010 mass %ASTM D482 / ISO 6245
Lubricity (corrected wear scar), max
520 µmISO 12156-1
03 HOW IT IS MADE

From refining to the bunker tank.

Marine fuel is a product of petroleum refining, prepared to a specification before delivery.

  1. 01

    Distillation

    Crude oil is distilled. Lighter fractions become distillate marine fuels; the heavy residue is the base of residual fuels.

  2. 02

    Blending

    Residual fuel is blended with gas oil to a target viscosity to make intermediate grades such as IFO 180 and IFO 380.

  3. 03

    Testing

    Each batch is tested against the agreed grade, including viscosity, density, flash point and sulphur.

  4. 04

    Delivery

    The fuel is delivered by road tanker, barge or ship-to-ship, with the Certificate of Analysis.

Crude oilFurnaceVacuumCutter stockFuel oilDrums · bulk01Distillation02Blending03Testing04Delivery
04 APPLICATIONS

Where DMX is used.

05 SAFETY & HANDLING

Flammable distillate. Handle by the SDS.

A summary of the statements a typical gas oil SDS carries. It does not replace the SDS of the offered grade.

Danger
  • H226 Flammable liquid and vapour (typical SDS).
  • H304 May be fatal if swallowed and enters airways.
  • H315 Causes skin irritation.
  • H332 Harmful if inhaled.
  • H351 Suspected of causing cancer.
  • H373 May cause damage to organs through prolonged or repeated exposure.
  • H411 Toxic to aquatic life with long lasting effects.
UN
UN 1202, gas oil · per SDS
Class
3, flammable liquid · PG III, per SDS
  1. 01
    Flammable liquid

    Flash point min. 43 °C. Keep away from heat, sparks, open flames and hot surfaces; earth and bond transfer equipment.

  2. 02
    Aspiration hazard

    May be fatal if swallowed and enters airways. Do not induce vomiting.

  3. 03
    Health

    Harmful if inhaled; causes skin irritation; suspected of causing cancer; may damage organs through prolonged or repeated exposure (typical SDS). Wear gloves and eye protection and avoid breathing mist or vapour.

  4. 04
    Environment

    Toxic to aquatic life with long lasting effects. Contain spills and keep the fuel out of drains and water.

  5. 05
    Hydrogen sulphide

    Observe the hydrogen sulphide limit, ventilate tanks before entry and follow the SDS for handling.

Plan storage, heating and treatment.
Keep itClean and dry

Good fuel management protects the engine. Confirm these points with your engine maker.

  • Cold flowCheck the pour point and, for DMX, the cloud point against the storage temperature in your climate.
  • TreatmentPurifiers, centrifuges and filters remove water and solids before the fuel reaches the engine.
  • CompatibilityDo not mix fuels from different suppliers without a compatibility check; incompatible fuels can form sludge.
  • SafetyObserve the flash point and hydrogen sulphide limits, ventilate tanks and follow the SDS for handling.
Standards and regulatory reference.
  • HS code2710.19
  • UN numberUN 1202
ISO 8217
Specification for marine fuels, category DMX. The catalogue values follow the 2010 edition and are archived references.
MARPOL Annex VI
The IMO global sulphur limit is 0.50% by mass, and 0.10% in SOx emission-control areas, unless an approved equivalent compliance method applies.
Bunker Delivery Note
Provided for marine bunkering as required by MARPOL.
Test methods
ASTM and ISO methods are cited beside each property, for example ASTM D445 for viscosity and D93 for flash point.
06 DELIVERY

Delivery format.

Delivery methods depend on the location, quantity and the receiving facilities. Confirm the arrangement for DMX.

Plan your order

How many containers is that?

Typical loads used for planning. Your offer confirms the exact packing and load for the product and source.

4road tankers
road tankers
4
Last road tanker
33% full
  • Minimum orderBy grade and delivery methodShip to ship, drums or bulk; confirmed with the quote
  • BunkeringShip to shipAt UAE anchorages, on agreed delivered terms
  • DocumentsCoA with every deliveryBunker Delivery Note for bunkering; MSDS on request
07 BUYING THIS GRADE

Before you order.

01What is DMX used for?

Confirm the fuel against the engine maker’s requirements and the applicable ISO 8217 edition. Share the vessel, voyage and sulphur requirement and we will confirm the offered product.

02Which ISO 8217 edition do the values follow?

The values shown are archived ISO 8217 (2010) catalogue references. The specification for the actual offered product is agreed in the enquiry.

03What documents come with each delivery?

Every delivery includes a Certificate of Analysis. Certificate of Origin, MSDS and third-party inspection reports are available on request.

04How is the fuel delivered?

Delivery by road tanker, barge, ship-to-ship transfer or shore tank depending on the location and quantity. Share the port or receiving site so the team can confirm.

05What is the minimum order quantity?

MOQ depends on the grade, delivery method and location. Share your requirement and we will confirm feasibility with the quote.

06What is the difference between distillate and residual marine fuel?

Distillates (DM grades) are lighter, cleaner fuels. Residual grades (RM) are the heavier fuels left after refining. Intermediate grades such as IFO 380 blend residual fuel with gas oil to reach a target viscosity.

07Which grade does my engine need?

Follow the engine maker’s fuel requirements. Share the engine and voyage and we will confirm the grade and sulphur limit.

08What does low-sulphur mean for bunker fuel?

A low-sulphur label alone does not establish compliance. The IMO global sulphur limit is 0.50% by mass, and the limit in SOx emission-control areas is 0.10%, unless an approved equivalent compliance method applies. Specify the limit required for your route.

FROM SPECIFICATION TO SUPPLY

Let’s talk DMX marine fuel.

Share the grade, specification, quantity, delivery method and location. Our team replies with the offer within 24 hours. We reply with a firm FOB, CFR or CIF offer, usually within 24 hours.

  • Grade, ISO 8217 edition and sulphur limit
  • Road tanker, barge or ship to ship
  • Certificate of Analysis with every delivery
Request a quote
FROM THE KNOWLEDGE CENTRE

Guides & articles

Written by our trade desk to help you specify, compare and buy with confidence.

All guides & articles
ArticleFuel oil · 2 minWhy a fuel tank holds more than its rated capacity

It seems like the fuel tank is filled up more than the rated capacity!!! It’s never been like that!!! Driver may have all…

Read
ArticleFuel oil · 2 minWhat exhaust gas colour tells you

The color of exhaust gas slightly differs from vehicles, but is usually divided into colorless, white, black, and blue-gray.…

Read
ArticleFuel oil · 3 minFuel oil for power generation and industrial heating

How residual and distillate fuel oils are used in boilers, furnaces and generator sets, and why viscosity and preheating drive…

Read
GuideFuel oil · 3 minISO 8217 residual fuel specification explained

A reference to the ISO 8217 residual marine fuel grades: how they are named, the key RMG 380 limits and what each parameter…

Read
GuideFuel oil · 3 minFuel oil storage, heating and transfer temperatures

How to set storage, transfer and preheat temperatures for heavy fuel oil using pour point, flash point and the…

Read
GuideFuel oil · 3 minSampling and testing fuel oil deliveries

How fuel oil deliveries are sampled, labelled and retained, what the bunker delivery note must show and how testing protects both…

Read
LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote