Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read5 sections

Knowledge centre · Fuel oil & engines

Fuel oil for power generation and industrial heating

How residual and distillate fuel oils are used in boilers, furnaces and generator sets, and why viscosity and preheating drive handling.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of a vessel taking on marine fuel oil
On this page · 5 sections
  1. 01Distillate and residual grades
  2. 02Where it is used
  3. 03Why viscosity and preheating come first
  4. 04Other properties that affect operation
  5. 05Specifying fuel oil for a heating or power application

Fuel oil covers a family of petroleum fuels, from light distillates close to diesel through to heavy residual oils left after the lighter fractions have been distilled out of crude oil. Heavy grades remain in use for steam raising, process heating and power generation, especially at sites that already have oil-fired equipment or need a fuel they can store on site.

This article explains where fuel oil is used in power and heat, and what users need to get right when handling it.

Distillate and residual grades

The lighter grades are distillates. They flow at ambient temperature, burn cleanly and are used in smaller burners and diesel engines. The heavier grades are residual or blended residual fuels. They are cheaper per tonne but much more viscous, and they usually carry more sulphur, ash and carbon residue.

In the older US numbering, No. 2 is a distillate heating oil, No. 4 is a light commercial heating oil that can be burned without preheating, and No. 5 and No. 6 are residual fuels that need heating before they will pump and atomise. British Standard BS 2869 uses classes, with the heavier classes F, G and H always needing heat. Marine residual fuels are graded under ISO 8217, with viscosity limits set at 50 °C.

Where it is used

  • Industrial boilers. Steam for process plants, refineries, food factories and textile mills. Many older boilers were designed for heavy fuel oil.
  • Furnaces and kilns. Direct-fired process heat, where the fuel's heating value per tonne and its storage convenience count.
  • Power plants and generator sets. Heavy fuel oil has largely been displaced by gas for base-load power in many regions, but it is still used for backup, peaking and off-grid generation, and in medium-speed diesel engines built to burn it.
  • Start-up fuel. Oil is also used to light up and stabilise solid-fuel boilers.

Why viscosity and preheating come first

Viscosity tells you how easily a fuel can be pumped and how well it will atomise at the burner. Density alone says little about how a fuel will burn. A heavy residual fuel that is a thick semi-solid in a cold tank has to be warmed for storage, warmed again for pumping, and heated further so it reaches the burner at the viscosity the burner manufacturer specifies.

StageTypical approach for heavy fuel oil
StorageTank kept warm with steam or electric coils so the oil stays mobile.
TransferHeated, insulated lines; pumps sized for viscous fuel.
BurningFinal heater brings the fuel to the burner's target atomising viscosity.

Reference sources put No. 6 oil at roughly 104 to 127 °C for atomising, and BS 2869 Class G at around 40 °C in storage, 50 °C for pumping and 90 to 120 °C at the burner. These are indications only. The burner or engine maker's viscosity-temperature curve should always govern. Overheating is a problem too: it can crack the fuel and leave carbon deposits.

Trying to pump cold heavy fuel oil is a well-known cause of damaged pumps, lines and burners. Check the fuel's viscosity against your heating capacity before you buy.

Other properties that affect operation

  • Sulphur. Forms sulphur oxides on combustion, which can corrode cooler parts of the boiler and are subject to local emission limits.
  • Ash, vanadium and sodium. Contribute to fouling and high-temperature corrosion of boiler tubes and engine components.
  • Water and sediment. Cause unstable flames and filter blockages; tanks should be drained regularly.
  • Flash point. Matters for safe storage and handling; follow the product SDS.
  • Carbon residue. An indicator of the fuel's tendency to form deposits.

Specifying fuel oil for a heating or power application

An enquiry should state the grade or viscosity class you burn, the maximum viscosity your heating system can handle, sulphur and ash limits required by your equipment or permit, flash point minimum, monthly volume and how you receive fuel (bulk vessel, road tanker or ISO tank). Ask for the CoA for each lot and, where relevant, independent inspection of quantity and quality at loading.

Nuroil supplies fuel oil to industrial and power users on FOB, CFR or CIF terms. See our petroleum and energy page for related products.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote