Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read6 sections

Knowledge centre · Fuel oil & engines

How marine and industrial buyers plan petroleum product supply

A practical approach to planning fuel and lubricant supply: forecasting, specifications, sampling, documents and storage on site or on board.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of a vessel taking on marine fuel oil
On this page · 6 sections
  1. 01Start with consumption and lead times
  2. 02Fix the specification before the price
  3. 03Sampling and documents
  4. 04Storage on site and on board
  5. 05Working with suppliers
  6. 06What to put in a supply enquiry

For a ship operator, a power plant or a factory, running out of fuel or lubricant stops work. Receiving the wrong quality can be worse, because it damages equipment before anyone notices. Good supply planning reduces both risks without tying up too much cash in stock.

This article sets out how experienced marine and industrial buyers approach fuel oil and lubricant supply.

Start with consumption and lead times

Every plan starts with an honest consumption figure for each product: tonnes of fuel per month, litres of each lubricant per month, and how those change with running hours, seasons or voyage patterns. Then add the lead time from enquiry to delivery, including loading, sea transit, customs clearance and inland transport.

  • Set a minimum stock level that covers consumption during the full lead time plus a safety margin.
  • Set a reorder point above that minimum, so the next order is placed before stock gets tight.
  • Check storage capacity: a full parcel must physically fit into available tanks or warehouse space when it arrives.

Fix the specification before the price

Quotations can only be compared if they are for the same product. For marine fuels, buyers typically specify an ISO 8217 grade and edition, and set the sulphur limit to match the rules that apply where the fuel will be used. For industrial fuel oil, the specification usually lists viscosity, density, sulphur, flash point, water, ash and carbon residue limits. For lubricants and base oils, it lists the grade, viscosity range, viscosity index and appearance, and names the test methods.

Writing the specification down, with test methods, avoids disputes about whether a product was on specification when it arrived.

Sampling and documents

Samples and paperwork are the buyer's evidence if something goes wrong. In bunkering, regulations require a bunker delivery note and a sealed representative sample with every delivery; the note stays on board for at least three years and the sample for at least twelve months. Commercial samples taken at an agreed point, ideally by continuous drip during the whole transfer, are what a laboratory tests against ISO 8217 if quality is challenged.

Document or recordPurpose
Certificate of analysis (CoA)Shows the lot's tested properties against specification.
Delivery note or bill of ladingConfirms product, quantity and date of delivery.
Sealed samples with recorded seal numbersAllow independent testing if a dispute arises.
Safety data sheet (SDS)Handling, storage and emergency information.
Inspection or survey reportIndependent check of quantity and quality, where agreed.

Quantity deserves the same attention as quality. Fuels are sold by weight but delivered by volume, so temperature and density corrections matter, and many buyers appoint an independent surveyor for larger deliveries.

Storage on site and on board

Received product has to stay on specification until it is used. Fuel tanks should be drained of water regularly and kept at the right temperature for heavy grades. Lubricants and base oils should be stored indoors where possible, in a cool, dry place, with first-in first-out rotation. Drums kept on deck or outdoors should be raised off the ground, covered and positioned so water cannot collect around the bungs.

Working with suppliers

Buyers who share forecasts with their suppliers tend to get more reliable delivery. Practical habits include:

  • Agreeing standard specifications and packing so that repeat orders need minimal re-checking.
  • Qualifying more than one source for critical products.
  • Reviewing each delivery's CoA before use, and keeping retained samples for an agreed period.
The cheapest parcel is rarely the cheapest outcome if it arrives late, off specification or without the documents needed to prove what it is.

What to put in a supply enquiry

List each product and grade, the specification and test methods, monthly volume and delivery frequency, packing (bulk, ISO tank, flexitank, drums), destination port and preferred terms (FOB, CFR or CIF). Ask for a recent CoA and the SDS, and state whether you require a certificate of origin or third-party inspection.

Nuroil supplies fuel oil and base oils worldwide. You can send a consolidated enquiry through our quote request form.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote