Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read5 sections

Knowledge centre · Fuel oil & engines

What the 180 and 380 in fuel oil grades mean

IFO 180 and IFO 380 are viscosity limits, not quality ratings. What the numbers measure, how they map to ISO 8217 and why they matter on board.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of a vessel taking on marine fuel oil
On this page · 5 sections
  1. 01The number is a viscosity ceiling
  2. 02How the trade names map to ISO 8217
  3. 03Why viscosity matters in practice
  4. 04Choosing between 180 and 380
  5. 05What to put in an enquiry

Ask for intermediate fuel oil and the first question back is usually which number: 180 or 380. Those figures are not quality ratings and they say nothing about sulphur. They describe how thick the fuel is allowed to be, and that decides how much heat the receiving ship or plant must put into it before it can be pumped and burned.

The number is a viscosity ceiling

IFO stands for intermediate fuel oil, a residual fuel made by blending heavy refinery residues with lighter components. The number after it is the maximum kinematic viscosity in centistokes (cSt) measured at 50°C. An IFO 380 may not exceed 380 cSt at that temperature, and an IFO 180 may not exceed 180 cSt. One centistoke equals one square millimetre per second, so specification sheets often show the same limit in mm²/s.

The figure is a maximum, not a typical value. A cargo sold as 380 might measure 300 cSt or 370 cSt and still be on specification. If your equipment needs a narrower window, the contract has to say so.

How the trade names map to ISO 8217

The international marine fuel standard, ISO 8217, uses letter codes rather than the old IFO labels. Residual grades start with RM (residual marine), followed by a category letter and the viscosity limit. IFO 180 is usually traded as RME 180 or RMG 180, and IFO 380 as RMG 380. The RMG category also includes 500 and 700 cSt variants, which share the same density ceiling but allow thicker fuel. The heavier RMK grades permit higher density as well.

Older paperwork sometimes uses codes based on viscosity at 100°C, which is why labels such as RMG 35 can still appear alongside IFO 380. Heavy fuel viscosity was traditionally quoted at 100°C, and some engine makers still publish data that way, so always check which reference temperature a figure refers to before comparing two numbers.

Why viscosity matters in practice

Residual fuel is far too thick to atomise at ambient temperature. Viscosity falls steeply as the fuel is heated, so the 50°C reference simply gives buyer and seller a fixed point of comparison. What an engine actually needs is a much lower viscosity at the injector, typically in the range of about 10 to 15 cSt. Fuel that reaches the nozzle too thick breaks into large droplets that do not burn completely, leaving deposits and wasting fuel.

The higher the grade number, the hotter the fuel must be heated to reach that injection viscosity, and every heating system has a limit. One marine fuel testing laboratory described a delivery ordered as IFO 380 that measured about 606 cSt at 50°C. Every other tested parameter was within limits, but reaching the required viscosity would have meant heating the fuel to around 136°C, which the vessel could not do. The fuel was declared off-specification and became the subject of a commercial claim.

The number on an IFO grade tells you how thick the fuel may be, not how clean or how good it is.

Choosing between 180 and 380

  • Heating capacity. Compare the maximum outlet temperature of your fuel heaters with the viscosity–temperature chart for the grade. If the heaters cannot reach injection viscosity with a margin to spare, choose a lighter grade.
  • Engine type. Large slow-speed engines commonly run on 380 cSt fuel. Smaller medium-speed engines and auxiliary plant are often specified for lighter grades, so check the engine maker's fuel recommendations.
  • Storage and transfer. Thicker fuel needs more tank heating and higher transfer temperatures, which matters most in cold climates and on long voyages.
  • Everything else. Viscosity tells you nothing about sulphur, density, catalyst fines or stability. Each of these has its own limit in ISO 8217 and must be specified separately.

What to put in an enquiry

When requesting fuel oil or bunker and marine fuel, state the ISO 8217 grade and edition (for example RMG 380 to ISO 8217:2017), the maximum sulphur content you need, quantity, delivery port and terms. If your equipment needs a lower viscosity than the grade allows, write the actual maximum into the specification rather than relying on the grade name. Nuroil supplies a certificate of analysis with every delivery, so you can check the measured viscosity at 50°C against your heater capacity before the fuel goes into use. Send your requirements through the quote request form.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote