Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read8 sections

Knowledge centre · Industrial chemicals

Storing LABSA: tank materials, drums, IBCs and shelf life

A reference on storing LABSA 96%: suitable tank and drum materials, packing options, temperature, moisture control and how long the acid keeps.

Written by the Nuroil trade desk, Sharjah

On this page · 8 sections
  1. 01Packing options
  2. 02Tank and line materials
  3. 03Keeping it dry
  4. 04Temperature and viscosity
  5. 05Shelf life and stock rotation
  6. 06Day tanks and dosing vessels
  7. 07Receiving checklist
  8. 08Agreeing packing with your supplier

LABSA 96% is stable if it is kept dry, cool and in the right containers. Most storage problems come from moisture, unsuitable metals or long periods at high temperature. This guide covers what to store it in, how to receive it, and how long it can be held.

Packing options

PackingSuitsPoints to watch
HDPE drumsSmall and medium detergent makersKeep bungs tight; store out of direct sun
IBCs (about 1 m³)Regular users with forklift handlingCheck valve and gasket material suit strong acids
ISO tank containersPlants with bulk storage tanksAgree discharge method and any heating in advance
FlexitanksBulk users with suitable receiving tanksConfirm the liner is approved for the product

Whatever the packing, check that the transport classification and labels match the SDS, since LABSA travels as a corrosive liquid.

Tank and line materials

  • Stainless steel is the usual choice for tanks, pumps and lines. Confirm the grade with your engineer, especially if the acid may pick up water or chlorides.
  • Acid-resistant fibreglass (FRP) and suitable plastics such as HDPE are widely used for tanks and day vessels.
  • Carbon steel and iron appear in some supplier storage notes, but dry acid is the condition for that. Once the acid picks up moisture it becomes much more aggressive to plain steel, and corrosion products can darken it. Many users avoid unlined carbon steel for that reason.
  • Avoid copper, brass, aluminium and galvanised fittings in contact with the acid.

Keeping it dry

Supplier storage guidance consistently says to keep LABSA away from moisture and water. In practice:

  • keep drums and IBCs closed between uses and store them under cover;
  • fit bulk tanks with a vent that limits humid air entry, such as a desiccant breather;
  • never wash a tank or line with water and then refill without draining and drying it.

Temperature and viscosity

LABSA is viscous and becomes harder to pump in cool weather. If it must be warmed, use gentle, controlled heating such as a warm room, a drum heater with thermostat or low-temperature coils, rather than steam directly on the container wall. Long periods at elevated temperature encourage darkening, so warm only what you need. In hot climates, keep drums shaded; sun on dark drums can raise the contents' temperature well above the air temperature.

Shelf life and stock rotation

Supplier data commonly give a shelf life in the order of two years from manufacture when stored correctly, though some producers state shorter periods. Colour is usually the first property to drift. Good practice:

  • record the production date and lot number on receipt;
  • use first in, first out;
  • retest colour and active matter if stock is held near the end of its stated shelf life.

Day tanks and dosing vessels

Many plants decant LABSA from drums into a smaller day tank above the mixer. Keep that tank covered, fit a level indicator so operators do not overfill it, and place it in a bunded area that can hold its full contents. Drain and dry it before changing to another material.

Receiving checklist

  1. Check labels, UN number and lot number against the documents.
  2. Inspect containers for leaks, bulging or damaged closures.
  3. Take a sample and compare appearance and, if possible, colour with the CoA.
  4. Move containers to the designated corrosive store, segregated from alkalis and oxidisers.
Dry, closed, shaded and in acid-resistant materials: those four conditions prevent most LABSA storage problems.

Agreeing packing with your supplier

When you enquire, state the packing you can receive (drums, IBCs or bulk), the delivery port, and any limits on drum weight for your handling equipment. Nuroil supplies LABSA on FOB UAE terms, with CFR or CIF on request, and a CoA with every lot. Send the details through request a quote.

KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote