Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Bitumen

PMB designations and EN 14023 classes explained

How to read a PMB designation such as PMB 45/80-65, what each EN 14023 property and class covers, and how other grading systems describe PMB.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of polymer modified bitumen blending
On this page · 6 sections
  1. 01Reading a PMB designation
  2. 02How classes work
  3. 03Main properties in EN 14023
  4. 04Common grades and typical uses
  5. 05Relation to performance grades
  6. 06What to request from the supplier

Polymer modified bitumen is sold under several naming systems. In Europe and many export markets the reference is EN 14023, which uses designations such as PMB 25/55-55 or PMB 45/80-65. In North America and much of the Middle East, modified binders are more often described by performance grade, for example PG 76-22 with additional recovery requirements. This guide explains the European system and how it relates to the others.

Reading a PMB designation

An EN 14023 designation has three numbers. The first two give the penetration range at 25 °C in tenths of a millimetre; the third gives the minimum ring-and-ball softening point in °C. So PMB 45/80-65 is a binder with penetration between 45 and 80 dmm and a softening point of at least 65 °C. PMB 25/55-55 is harder, with penetration of 25 to 55 dmm and a softening point of at least 55 °C.

The designation alone does not fully define the product. EN 14023 is a framework: each property is specified by choosing a class from a table of options, and the full set of chosen classes, set out in a national annex or in the product's declaration of performance, defines the binder.

How classes work

For each property the standard lists numbered classes with different limits. For several properties, a lower class number means a more demanding requirement. On published declarations, for example, elastic recovery above 80 per cent appears as class 2 while 50 per cent appears as class 5. A property that a country does not require can be declared as "NPD", meaning no performance determined. When comparing two PMB offers, compare the class or numerical limit for each property, not just the designation.

Main properties in EN 14023

PropertyTest methodWhat it tells you
Penetration at 25 °CEN 1426Consistency at service temperature
Softening pointEN 1427Resistance to softening in hot weather
Elastic recovery (25 °C or 10 °C)EN 13398Presence and effectiveness of an elastomer network
Force ductility or tensile testEN 13589 / EN 13703, EN 13587Cohesion and energy under stretching
Fraass breaking pointEN 12593Brittleness at low temperature
Storage stabilityEN 13399Tendency of polymer and bitumen to separate in hot storage
Resistance to hardening (RTFOT)EN 12607-1Mass change, retained penetration and softening point rise after short-term ageing
Flash pointEN ISO 2592Safety margin for heating

Common grades and typical uses

  • Harder grades (e.g. PMB 10/40-65, PMB 25/55-55) are used in base and binder courses and heavily loaded surfaces where stiffness matters most.
  • Mid-range grades (e.g. PMB 45/80-55, PMB 45/80-65) are widely used in wearing courses, stone mastic asphalt and porous asphalt.
  • Softer grades (e.g. PMB 75/130-60) suit colder climates, thin surfacings and some surface dressing work.

National practice varies, so always check which grades and classes the project specification names.

Relation to performance grades

There is no exact conversion between an EN 14023 designation and a Superpave performance grade, because the two systems use different tests. A PG binder is graded from rheological measurements at the actual pavement design temperatures, while EN 14023 relies mainly on empirical tests at fixed temperatures. Where a project uses performance grades, modification is usually signalled by a high-temperature grade of 76 °C or above, by a wide spread between high and low grades, and by MSCR recovery or elastic recovery limits.

A PMB designation tells you the penetration range and minimum softening point; the class table tells you everything else.

What to request from the supplier

Quote the full designation and, where possible, the required class for each property, or attach the relevant national annex or tender table. Ask for a declaration of performance or product data sheet, a CoA per batch including storage stability and RTFOT results, and recommended storage and mixing temperatures. Nuroil sources PMB from established producers and supplies a CoA with every delivery; contact us through the quote request form.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote