Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read5 sections

Knowledge centre · Urea & fertilizers

How merchant-grade phosphoric acid (MGA) is used to make phosphate fertilizers

What merchant-grade phosphoric acid is, how it becomes MAP, DAP and TSP, and why its P2O5, solids and impurity levels matter to granulation plants.

Written by the Nuroil trade desk, Sharjah

Illustration of a young plant growing in field soil
On this page · 5 sections
  1. 01What merchant-grade acid is
  2. 02How MGA becomes fertilizer
  3. 03Why impurities and solids matter
  4. 04Handling and storage
  5. 05What to specify when buying MGA

Most of the world's phosphoric acid never reaches a laboratory or a food plant. Around nine-tenths of it goes into fertilizers, and the form that moves between producers and fertilizer plants is usually called merchant-grade acid, or MGA. It is a concentrated, wet-process acid made for ammoniation and granulation, not for purity. This article explains what MGA is and what a fertilizer producer needs to know about it.

What merchant-grade acid is

Wet-process phosphoric acid is made by digesting phosphate rock with sulphuric acid. The reaction produces a slurry of acid and gypsum, which is filtered off. The filtered acid is fairly weak, typically in the region of 23 to 33% P2O5, so it is evaporated to concentrate it before it is stored or traded.

In trade, MGA is generally described as wet-process acid concentrated to roughly 52 to 54% P2O5. Strength is quoted as P2O5 rather than H3PO4 because fertilizer content is declared that way. Unlike purified acid, MGA keeps most of the impurities that came from the rock: iron, aluminium, magnesium, fluoride, sulphate, organic matter and some suspended solids. These give it its typical dark green to black colour.

How MGA becomes fertilizer

  • MAP and DAP: phosphoric acid is reacted with ammonia in a pre-neutraliser or pipe reactor and then granulated. The ratio of ammonia to acid decides whether the product is mono-ammonium phosphate (commonly 11-52-0) or di-ammonium phosphate (18-46-0).
  • TSP: triple superphosphate is made by reacting phosphate rock with phosphoric acid rather than sulphuric acid, which gives a much higher phosphate content than single superphosphate.
  • NPK compounds: granulation plants use MGA as a phosphate source alongside ammonia, potash and other nitrogen materials.
  • Liquid fertilizers: more concentrated superphosphoric acid, above about 70% P2O5, is used to make ammonium polyphosphate solutions. Ordinary MGA is the starting point for that further concentration.

For background on choosing between the two main ammonium phosphates, see our existing piece on DAP and MAP.

Why impurities and solids matter

Impurities in MGA are not just a cosmetic issue. Research on DAP granulation has linked the combined iron and aluminium oxide content of the acid to changes in granule size and growth. Metal impurities also form complex phosphates that are less water-soluble, which can shift the declared soluble P2O5 in the finished product. Magnesium raises the viscosity of the acid and the slurry.

Suspended solids keep precipitating after the acid has been made, especially as it cools and ages. In storage tanks and ship tanks this shows up as sludge on the bottom. Plants handle it with agitation, periodic desludging and by agreeing a maximum solids figure in the contract.

MGA is bought on P2O5, but it is processed on its impurities. Solids, iron, aluminium and magnesium decide how smoothly a granulation plant runs.

Handling and storage

MGA is corrosive, warm when it leaves the evaporators, and contains fluoride and chloride that attack ordinary stainless steel. Storage tanks are commonly rubber-lined carbon steel, and pipework and pumps use lined or suitably rated alloy materials. Large volumes move in dedicated bulk tankers and lined road or rail tanks rather than small packs. As with any phosphoric acid, it reacts with exposed metals to release hydrogen, so tanks should be vented and kept away from ignition sources during maintenance.

What to specify when buying MGA

A useful enquiry from a fertilizer producer states:

  • P2O5 content (minimum, and the analysis method).
  • Maximum suspended solids and the sampling point.
  • Maximum iron, aluminium and magnesium oxides, plus fluoride and sulphate.
  • Delivered temperature limits, if your tanks or linings are temperature sensitive.
  • Delivery form and volume, and how quantity will be measured at discharge.

Ask for a certificate of analysis per lot and agree whether independent inspection at loading is required. Nuroil supplies phosphoric acid on request with a CoA, and can arrange third-party inspection when asked. For related products see our fertilizers range, or send your specification through the quote request form.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote