Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read10 sections

Knowledge centre · Industrial chemicals

LABSA 96% specification: active matter, free acid, free oil and colour

A parameter-by-parameter reference to the LABSA 96% specification, with typical commercial limits and what each test means for detergent makers.

Written by the Nuroil trade desk, Sharjah

On this page · 10 sections
  1. 01Typical specification
  2. 02Active matter
  3. 03Neutralisation value
  4. 04Free sulphuric acid
  5. 05Free oil
  6. 06Water
  7. 07Colour
  8. 08Other items sometimes reported
  9. 09Checking a delivery against the specification
  10. 10Using the specification in a purchase

LABSA 96% is not covered by one universal standard. Each producer publishes its own specification, but the same handful of parameters appear on almost every certificate of analysis. This guide explains each one and gives the ranges commonly seen in commercial specifications, so you can compare offers on an equal footing.

Typical specification

The values below are drawn from published producer and supplier data sheets. They are indicative; your contract should fix the limits and test methods.

ParameterCommonly specified limitWhat it tells you
Active matter (as LAS acid)96% minSurfactant content you are paying for
Neutralisation value / total acidityAbout 175 to 188 mg KOH/gAlkali needed to neutralise, including free sulphuric acid
Free sulphuric acid (H₂SO₄)About 1.3 to 1.5% maxInorganic acid left from sulphonation
Free oil (unsulphonated matter)About 1.8 to 2.0% maxUnreacted alkylbenzene and by-products
WaterAbout 0.5 to 1.0% maxMoisture added for stabilisation or picked up later
Colour (Klett, 5% active solution)About 40 to 50 maxShade the surfactant brings to the product

Active matter

This is the sulphonic acid content and the headline number in "LABSA 96%". It is normally determined by titration, and the result depends on the molecular weight assumed for the alkylbenzene, so a CoA should state the basis. A shortfall of one or two points directly reduces the surfactant in each tonne of finished detergent.

Neutralisation value

Also called total acidity or acid value, this measures all the acid present, sulphonic and sulphuric together, expressed as mg of potassium hydroxide per gram. It is the most practical number for calculating caustic soda or soda ash dosing. Standard methods such as ASTM D4711 are used by some producers for acidity and free sulphuric acid.

Free sulphuric acid

Sulphonation with sulphur trioxide leaves a small amount of sulphuric acid. On neutralisation it becomes sodium sulphate. In powders that is harmless filler; in liquids it adds electrolyte that changes viscosity. A higher level also makes neutralisation more exothermic.

Free oil

Free oil is the material that did not sulphonate, mainly alkylbenzene plus some sulphones. It contributes no detergency and, at high levels, can cause haze or odour in liquid products. Ageing at the producer converts part of the unreacted alkylbenzene into active matter, which is why properly aged acid has lower free oil.

Water

Producers add a small amount of water after ageing to hydrolyse anhydrides and stabilise the acid. Beyond that, extra water usually means moisture pick-up in storage. Wet acid is more corrosive to steel and, in powders, adds to the drying load.

Colour

Klett colour is measured on a dilute solution, usually 5% active matter, and rises with darker acid. It matters most for clear liquid detergents. Some producers also use AOCS methods for colour; confirm the method so that two certificates are comparable.

Other items sometimes reported

  • Density and viscosity at a stated temperature, useful for pump and tank design.
  • Appearance, normally a brown viscous liquid free of suspended matter.
  • Alkyl chain distribution or mean molecular weight, which affects active matter calculation and performance.

Checking a delivery against the specification

If you have a laboratory, a simple incoming check of active matter by titration, neutralisation value and Klett colour on each lot will catch most problems. Keep a sealed retained sample from every delivery until the batch it went into has been sold, so any later complaint can be traced.

Compare offers on active matter, free oil, free sulphuric acid and colour together, and on the same test methods.

Using the specification in a purchase

Put the limits and methods in your purchase contract, ask for a CoA for each lot, and agree how a dispute would be settled (for example, by an independent laboratory on a retained sample). Nuroil provides a CoA with every delivery, with MSDS and third-party inspection on request. Share your specification through request a quote.

KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote