Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read8 sections

Knowledge centre · Industrial chemicals

How crude glycerine is refined to 99.5% grade

5% distilled glycerine: neutralisation, salt and fatty matter removal, vacuum distillation and bleaching.

Written by the Nuroil trade desk, Sharjah

On this page · 8 sections
  1. 01Step 1: pre-treatment and neutralisation
  2. 02Step 2: removing methanol and water
  3. 03Step 3: separating salts
  4. 04Step 4: vacuum distillation
  5. 05Step 5: bleaching and polishing
  6. 06Feedstock makes a difference
  7. 07What the steps mean for quality
  8. 08Questions to ask a supplier

Most of the world's refined glycerine starts as a crude stream from biodiesel plants, soap works or fat splitting. Turning that brown, salty liquid into clear 99.5% glycerine takes several separation steps. Knowing them helps buyers understand why grades differ and which impurities to watch.

Step 1: pre-treatment and neutralisation

Crude glycerine from biodiesel is usually alkaline because of the catalyst and contains soaps. Refiners add an acid, such as sulphuric or phosphoric acid, to neutralise it. This also splits soaps into free fatty acids, which separate as an oily layer that can be removed. The catalyst ends up as a salt, for example potassium sulphate when potassium catalyst and sulphuric acid are involved.

Soap-lye crude goes through a similar clean-up, but its main burden is common salt, which has to be dealt with in later stages.

Step 2: removing methanol and water

Biodiesel crude contains unreacted methanol. It is stripped off by heating, often under vacuum, and usually recovered for reuse. Water is evaporated at the same time. Producer descriptions of this stage report that it lifts glycerol to somewhere around 78 to 98% purity, depending on the plant. Material at this point is often sold as technical or partly refined glycerine.

Step 3: separating salts

As water is removed, salts become less soluble and crystallise out. They are separated by settling, filtration or centrifuging. Some refiners use ion exchange or membrane steps instead of, or in addition to, distillation, especially for sweet-water glycerine with low salt.

Step 4: vacuum distillation

Glycerine boils at about 290°C at atmospheric pressure and begins to decompose near that temperature, so it is distilled under deep vacuum with steam stripping at much lower temperature. Distillation leaves heavy residues, salts and high-boiling organics (often called glycerine foots or pitch) behind, and separates light ends. Some plants rectify the distillate further in a column to reach the target purity.

Step 5: bleaching and polishing

The distilled glycerine is passed over activated carbon to remove remaining colour and odour bodies, then filtered. European producers of distilled glycerine describe exactly this combination of rectification under reduced pressure and carbon adsorption to reach purity above 99.5% with low colour.

StageMain thing removedTypical result
NeutralisationAlkali, soaps (as fatty acids)Neutral crude
StrippingMethanol, waterAbout 78 to 98% glycerol
Salt separationCatalyst salts, sodium chlorideLow-ash feed for distillation
Vacuum distillationHeavy residues, remaining saltsWater-white distillate
Carbon treatmentColour and odour bodies99.5%+ refined glycerine

Feedstock makes a difference

Sweet water from fat splitting contains little salt and no methanol, so it is the easiest to refine. Soap-lye crude carries a heavy salt load. Biodiesel crude varies most, because plants differ in how well they strip methanol and remove soaps. Refiners blend and adjust their process to the feed, which is one reason two 99.5% lots can differ slightly in odour or trace impurities.

What the steps mean for quality

  • Colour reflects distillation and carbon treatment; low colour usually indicates a well-run refinery.
  • Residue on ignition, chlorides and sulphates show how well salts were removed.
  • Fatty acids and esters show how completely fatty matter was separated.
  • Odour can betray traces of methanol or fatty residues.

Pharmacopoeia grades add tests for glycols and other organic impurities, because the refined product goes into medicines and personal care products.

Distillation under vacuum, followed by carbon polishing, is what separates true 99.5% glycerine from merely concentrated crude.

Questions to ask a supplier

Ask whether the glycerine is distilled, the feedstock source, the grade standard it is certified to, and for a recent CoA showing assay, colour, water, residue on ignition and chlorides. Nuroil sources glycerine from established producers and sends a CoA with every delivery; enquire through request a quote.

KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote