Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read9 sections

Knowledge centre · Industrial chemicals

Glycerine 99.5% USP specification: test by test

5% certificate of analysis, the limits commonly seen, and what each one tells the buyer.

Written by the Nuroil trade desk, Sharjah

On this page · 9 sections
  1. 01Typical specification
  2. 02Purity, assay and water
  3. 03Specific gravity
  4. 04Salts and inorganic residues
  5. 05Organic impurities
  6. 06Colour and odour
  7. 07Red flags on a certificate
  8. 08USP compared with Ph. Eur.
  9. 09Ordering USP glycerine

A certificate of analysis for USP glycerine lists a dozen or more tests. Most come from the USP monograph; a few, such as colour, are commercial additions. This guide explains each item so buyers can read a CoA quickly and spot gaps. Limits below are typical of supplier specification sheets built on the monograph; the current official USP text always prevails.

Typical specification

TestTypical limitWhat it shows
Glycerol content (commercial)99.5% minPurity as sold
Assay (anhydrous basis)99.0 to 101.0%Glycerol on a dry basis per the monograph
WaterOften 0.5% max for 99.5% gradesMoisture content
Specific gravityNot less than 1.249Quick identity and dilution check
ColourLow (APHA or Hazen, often 10 to 15 max)Refining and storage quality
Residue on ignition0.01% maxInorganic salts left
Chloride10 ppm maxResidual salt
Sulphate20 ppm maxResidual sulphate from neutralisation
Chlorinated compounds30 ppm max (as Cl)Organic chlorine impurities
Fatty acids and estersNot more than 1 mL of 0.5 N NaOH consumedResidual fatty matter
DEG and EGMonograph limit; must passToxic glycol contamination

Purity, assay and water

Commercial sheets often lead with a single purity figure such as 99.5% or 99.7%. The monograph assay, by contrast, is stated on the anhydrous basis, so it describes the glycerol in the dry material. Glycerine is strongly hygroscopic, which is why water is reported separately and why a lot that met specification at the refinery can drift if containers are left open.

Specific gravity

Pure glycerol has a density of about 1.26 g/cm3. The monograph minimum of 1.249 catches gross dilution with water. Because diethylene glycol has a density close to glycerine's, specific gravity alone cannot prove identity.

Salts and inorganic residues

Residue on ignition, chloride and sulphate together show how thoroughly the refinery removed catalyst salts and common salt. High values point to incomplete distillation or contamination.

Organic impurities

  • Chlorinated compounds can arise from certain production routes and are limited separately.
  • Fatty acids and esters indicate fatty matter carried over from biodiesel or soap feedstocks; they affect odour and stability.
  • DEG and EG are tested by gas chromatography. This is the most safety-critical line on the CoA.
  • Related compounds and elemental impurities are covered by current pharmacopoeia general chapters; ask how the producer controls them.

Colour and odour

Pharmacopoeia glycerine should be clear, colourless and practically odourless. Colour is often reported on the APHA (Hazen) scale; a European distilled glycerine specification, for example, sets 15 Hazen maximum. Colour rises with heat and time, so it is also a useful storage check.

Red flags on a certificate

  • No DEG and EG result, or "complies" with no method named.
  • No monograph edition stated, only "USP grade".
  • A CoA that does not show the original manufacturer or the lot number on the containers.
  • Identical results on every lot over many months, which suggests copied rather than measured data.

USP compared with Ph. Eur.

The European Pharmacopoeia monograph covers similar ground but frames some impurities differently, for example as limits on total impurities. If your product is sold in several regions, ask for material certified to both monographs. Many refineries test to both as standard, but it should be stated on the CoA rather than assumed.

Read the DEG/EG result, water and residue on ignition first; they reveal the most about safety, handling and refining quality.

Ordering USP glycerine

State the monograph and edition, minimum glycerol content, maximum colour and whether you also need Ph. Eur. or food-grade compliance. Ask for a CoA for each lot and the manufacturer's name. Nuroil supplies a CoA with every delivery and can arrange third-party inspection; send your specification through request a quote.

KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote