Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Bitumen

Gilsonite grades and specification parameters explained

What softening point, ash, moisture, solubility, volatile matter and particle size mean on a gilsonite specification and how to match them to your use.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of natural gilsonite mining
On this page · 6 sections
  1. 01Softening point: the headline number
  2. 02The other key parameters
  3. 03Solubility and ash work together
  4. 04Particle size and physical form
  5. 05Reading two offers side by side
  6. 06What to put in your enquiry

Gilsonite is sold in many grades, and the names used by different producers rarely line up. What does line up is the test data. A buyer who understands the handful of parameters on a gilsonite specification can compare offers properly and choose the grade that suits drilling, asphalt, inks or foundry work. This guide explains each parameter and why it matters.

Softening point: the headline number

Commercial gilsonite grades are classified first by their ring-and-ball softening point, the temperature at which a small disc of the material softens enough for a steel ball to sink through it. The same method is used for bitumen, but gilsonite values are far higher, typically somewhere between about 150 and 220 °C. Patent literature describes grades at around 150, 160, 175 and 190 to 200 °C, and notes that softening point depends mainly on the vein from which the material is mined.

The right softening point depends on the job:

  • Drilling fluids: the grade is chosen with the expected downhole temperature in mind, so the particles soften enough to deform into pore spaces without melting away.
  • Asphalt modification: higher softening point grades give more stiffening per kilogram but need good mixing temperature to disperse.
  • Inks and coatings: lower softening point grades tend to dissolve faster in solvents and oils.

The other key parameters

ParameterWhat it tells youWhy it matters
Softening point (ring and ball)Temperature at which the solid begins to flowMain grading property; governs behaviour in heat
Solubility (in carbon disulphide or trichloroethylene)Share of the sample that is soluble organic materialHigh solubility means more active hydrocarbon and less inert matter
Ash contentMineral residue left after burningAsh is inert filler; low ash is preferred for inks and coatings
MoistureFree water in the productAffects weight paid for, flow of powder and dispersion
Volatile matter and fixed carbonHow the material behaves on heatingRelevant to foundry use and to fume during hot mixing
Specific gravityDensity relative to water, around 1.05Used for volume calculations in muds and mixes
Particle size (mesh)Fineness of powder or size range of granulesControls dispersion speed and dust levels
Sulphur contentSulphur bound in the hydrocarbonSometimes specified for emission or product reasons

Solubility and ash work together

Gilsonite as mined can carry small amounts of host rock. That inert material shows up twice on a specification: as ash, and as the part that does not dissolve in the test solvent. A grade with high solubility and low ash is nearly pure hydrocarbon, which is what ink and coating makers want. For some asphalt and drilling uses a slightly higher ash may be acceptable if softening point and particle size are right. Always compare solubility and ash together rather than in isolation.

Particle size and physical form

Gilsonite is sold as lumps, crushed granules and milled powder. Powder is often specified by mesh, such as material passing a 200 mesh sieve. Finer powder disperses faster in mud, oil or bitumen but is dustier and more prone to caking under load. Lumps are easier to store and less dusty but need crushing or melting before use. If your plant has no milling equipment, buy the particle size you will actually feed into the process.

Reading two offers side by side

  1. Check both quote the same test methods, especially for softening point and solubility solvent.
  2. Compare softening point ranges, not single numbers; a tight range means more consistent behaviour.
  3. Compare ash and moisture, since both reduce the useful hydrocarbon you pay for.
  4. Confirm the particle size distribution, not only the top sieve size.
  5. Ask whether results are typical values or guaranteed limits.
Choose gilsonite by test data, not by grade name. Softening point, solubility, ash and particle size together describe what you will actually receive.

What to put in your enquiry

State the end use, required softening point range, maximum ash and moisture, minimum solubility, particle size and packing. Ask for a certificate of analysis for each lot and the MSDS. Nuroil supplies gilsonite with a CoA on every delivery and can arrange third-party inspection on request; see the gilsonite page or request a quote.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote