Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read6 sections

Knowledge centre · Bitumen

Gilsonite as an asphalt modifier: wet and dry processes

How gilsonite stiffens paving bitumen, the difference between adding it to the binder or the mix, what research shows and how it compares with SBS.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of natural gilsonite mining
On this page · 6 sections
  1. 01What gilsonite does to bitumen
  2. 02Wet process and dry process
  3. 03What research has found
  4. 04Gilsonite compared with SBS polymer
  5. 05Practical tips for trials
  6. 06Specifying gilsonite for asphalt

Road engineers in hot regions often need a binder that resists rutting under heavy, slow traffic. Polymer modification is the familiar route, but gilsonite offers another: a natural, high-softening-point hydrocarbon that blends into bitumen and makes it stiffer at high service temperatures. This article explains how it is added, what it changes and where its limits lie.

What gilsonite does to bitumen

Gilsonite is rich in asphaltenes and nitrogen compounds and is fully compatible with bitumen. When dissolved into a paving binder it:

  • raises the softening point and viscosity of the binder;
  • lowers penetration, making the binder harder;
  • improves resistance to permanent deformation (rutting) at high temperatures;
  • can improve adhesion to aggregate and resistance to moisture damage.

Laboratory studies report that gilsonite raises the high-temperature performance grade of a base binder, and that the resulting mixes have higher strength and stiffness under static and repeated loading.

Wet process and dry process

Wet processDry process
Where gilsonite goesBlended into hot bitumen before mixingAdded to the aggregate in the asphalt plant
EquipmentHeated tank with agitation or a high-shear millFeeder at the mixer or drum, or manual addition by bags
ControlBinder can be tested and graded before useRelies on good mixing time and temperature to dissolve
Typical userBinder blending terminals and larger contractorsContractors adding a modifier at the plant

In the wet process the binder can be sampled and checked for softening point, penetration and viscosity before it reaches the plant, which gives the most predictable result. The dry process is simpler and avoids storing modified binder, but the gilsonite must dissolve during the short time the hot aggregate and bitumen are mixed. Finer powder and adequate mixing temperature help.

What research has found

Published studies give a generally positive but nuanced picture:

  • A highway study of mixes with gilsonite added at 4, 6 and 8 per cent by weight of binder found higher dry and wet indirect tensile strength, but no increase in Hveem stability.
  • Work on wet and dry processes found that both stiffened the mix and improved resistance to loading.
  • A review of gilsonite in asphalt pavements reports improvements in rheology, stability, rutting resistance and moisture sensitivity across many studies.

Most of this evidence comes from laboratory testing. Benefits depend on the base bitumen, aggregate and test method, so trial mixes are essential.

Gilsonite compared with SBS polymer

SBS polymer adds elasticity as well as stiffness: an SBS-modified binder recovers after being stretched, which helps against both rutting and cracking. Gilsonite mainly adds stiffness. That makes the binder more resistant to rutting but can make it more brittle at low temperatures and more prone to fatigue cracking if overused. Research has looked at combining the two, using gilsonite to replace part of the SBS while keeping high-temperature performance. In hot climates with little frost, gilsonite-modified binders can be a practical option; where low-temperature cracking is a concern, polymer modification or a combination is usually preferred.

Gilsonite is a stiffener, not an elastomer. It helps against rutting, but the dosage must be balanced against cracking resistance.

Practical tips for trials

  1. Start with the target binder grade or performance grade, then find the gilsonite dosage that reaches it.
  2. Test the modified binder for softening point, penetration, viscosity and, where specified, performance grade.
  3. Check that mixing and compaction temperatures still work with the stiffer binder.
  4. Run mix tests for rutting, moisture sensitivity and, if relevant, cracking.

Specifying gilsonite for asphalt

State whether you will use the wet or dry process, the required softening point range and particle size, the expected dosage and the packing that suits your plant. Ask for a CoA per lot. Nuroil supplies gilsonite as well as paving bitumen grades; details are on the gilsonite page.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote