Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read7 sections

Knowledge centre · Bitumen

Gilsonite in printing inks, coatings and foundry sand

Why ink, paint and foundry users add gilsonite: colour, gloss, binding and solvent solubility, and what grade properties matter in each case.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of natural gilsonite mining
On this page · 7 sections
  1. 01Printing inks
  2. 02Paints, stains and protective coatings
  3. 03Foundry sand
  4. 04What each use asks of the grade
  5. 05Handling in the plant
  6. 06Testing incoming material
  7. 07Buying gilsonite for formulations

Outside drilling and roads, gilsonite has a long history in industrial formulations. Its dark colour, solubility in hydrocarbon solvents and high softening point make it useful as a natural resin in printing inks, paints and protective coatings, and as a carbon-forming additive in foundry moulding sand. These uses tend to demand cleaner, more consistent grades than bulk construction uses.

Printing inks

Dark printing inks, especially black inks for gravure and offset printing, have long used gilsonite as a resin and colour carrier. It contributes in several ways:

  • Colour. Its own deep brown-black tone supports the pigment, so less carbon black may be needed for the same depth of colour.
  • Binding. Dissolved in the ink vehicle, it helps bind pigment to the paper.
  • Pigment wetting. It helps disperse pigment evenly through the vehicle.
  • Drying and hold-out. Its high softening point gives a firmer ink film once the solvent or oil has gone.

Lower softening point grades are generally preferred here because they dissolve more readily in aromatic solvents and ink oils.

Paints, stains and protective coatings

Gilsonite dissolves easily in aromatic and many chlorinated solvents without heating, which makes it convenient for solvent-borne coatings. It is used in dark protective coatings for metal and wood, in stains and in some sealants. In these products it adds water resistance, adhesion and chemical resistance, and acts as a lower-cost resin in black and dark-coloured systems. Because it is dark, it is not suitable for light-coloured finishes.

Foundry sand

In green-sand casting, molten metal is poured into moulds made of sand bonded with clay and water. Carbonaceous additives are mixed into the sand to improve the surface finish of castings. When hot metal reaches the mould face, the additive releases volatile matter that forms a thin layer of carbon between metal and sand. This reduces metal penetration and burn-on, so castings shake out cleaner and need less cleaning. Gilsonite is used in this role as a sand additive, alone or alongside other carbon sources. For foundry use, volatile matter, fixed carbon and particle size matter alongside softening point.

What each use asks of the grade

UseProperties that matter mostWhy
Printing inksLow ash, high solubility, consistent softening pointInert particles spoil print quality; the resin must dissolve fully
Paints and coatingsHigh solubility, low ash, fine particle sizeClean solutions and smooth films
Foundry sandVolatile matter, fixed carbon, particle sizeControls the carbon layer formed at the mould face
The cleaner the end product, the tighter the specification: inks and coatings need low ash and full solubility, while foundry users look first at volatile matter and fineness.

Handling in the plant

Ink and coating plants usually dissolve gilsonite powder or granules in solvent in a stirred vessel. Fine powder dissolves faster but is dustier, so dust extraction at the charging point is worthwhile. Gilsonite powder is a combustible organic dust, and the solvents involved are often flammable, so ignition control is important. Foundry users typically dose powder into the sand mixer along with clay and other additives. In all cases follow the product SDS for dust exposure and fire precautions.

Testing incoming material

Where a formulation is sensitive, check each lot for softening point, ash and solubility, and run a quick solution test in your own solvent to confirm it dissolves cleanly without residue. Keep a reference sample from each lot so any later quality question can be traced.

Buying gilsonite for formulations

Describe the end use, solvent system, maximum ash and minimum solubility, softening point range, particle size and pack size. Ask for a certificate of analysis for each lot and the MSDS. Nuroil supplies gilsonite grades through the gilsonite page; for technical questions you can contact us.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote