Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Fuel oil & engines

Furnace oil grades compared: IS 1593, ASTM D396 and BS 2869

A reference to the main national standards for industrial furnace oil, how their grades are defined and what to check when an enquiry quotes one of them.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of an industrial furnace fuel oil installation
On this page · 6 sections
  1. 01IS 1593: Indian standard for fuel oils
  2. 02ASTM D396: US specification for fuel oils
  3. 03BS 2869: British standard for non-marine fuel oils
  4. 04How to compare offers across standards
  5. 05Specification versus typical values
  6. 06Writing the grade into an enquiry

Furnace oil is sold against several different national specifications, and buyers often receive offers written to a standard they do not use themselves. The grades are not interchangeable one-for-one because the standards measure viscosity at different temperatures and set different limits. This guide summarises the three standards most often seen in industrial fuel oil enquiries and explains how to read them side by side.

IS 1593: Indian standard for fuel oils

IS 1593 covers residual fuel oils intended mainly for oil-fired furnaces and boilers. It defines four grades by kinematic viscosity measured at 50 °C. The table below summarises key limits as published by a major refiner; always check the current edition, since the standard has been revised over time.

GradeViscosity at 50 °C (cSt)Sulphur, max (% mass)
LV (low viscosity)up to 803.5
MV1 (medium viscosity)80 to 1254.0
MV2 (medium viscosity)125 to 1804.0
HV (high viscosity)180 to 3804.5

Common limits across the grades include a minimum flash point of 66 °C, ash not above 0.1% by mass, sediment not above 0.25% by mass and water not above 1.0% by volume. MV2, often marketed as 180 cSt furnace oil, is the grade most widely sold for boilers, thermic fluid heaters and industrial furnaces.

ASTM D396: US specification for fuel oils

ASTM D396 covers a family of fuel oil grades for burners, from light distillates to heavy residual fuels. The heaviest grades, No. 5 and No. 6, are the residual fuels that correspond broadly to furnace oil. No. 6 is intended for industrial burners and normally needs preheating for handling and atomising.

The specification sets limits for properties including viscosity, flash point, pour point, water and sediment, and ash. Viscosity for the residual grades is measured at a different temperature from IS 1593, so do not compare the numbers directly; convert using a viscosity-temperature chart or ask the laboratory to report both.

BS 2869: British standard for non-marine fuel oils

BS 2869 covers fuel oils for agricultural, domestic and industrial engines and burners. Classes C and D are distillates, while classes E, F, G and H are residual or residue-containing burner fuels. These heavier classes are defined by viscosity bands measured at 100 °C, with sulphur limits that differ by class and by local regulation. Class G is the class most often quoted for heavy fuel oil used in industrial boilers.

How to compare offers across standards

  • Check the test temperature for viscosity. 50 °C, 100 °C and other reference temperatures give very different numbers for the same oil.
  • Compare sulphur against your permit, not just the standard. Local emission rules may be stricter than any grade maximum.
  • Look at flash point. Most specifications set 66 °C as a minimum for residual fuels, which matters for storage classification and safe heating.
  • Read water, sediment and ash together. These drive filter loading, burner wear and fouling.
  • Ask for pour point. It decides whether tanks and lines need heating in your climate.
  • Note the edition of the standard. Limits change between revisions, so the offer should state the edition.
Two fuels sold under different standards can be very similar, or quite different. Compare the actual certificate values, not the grade names.

Specification versus typical values

A specification sheet gives limits; a certificate of analysis gives the measured result for a particular batch. Offers sometimes show typical values, which describe what the product usually looks like but are not guaranteed. For contract purposes, write the limits you need into the order and expect a CoA for each lot showing results against them.

Writing the grade into an enquiry

State the standard and edition you buy against, the grade or viscosity band, the maximum sulphur your site permits and any extra parameters your burner supplier requires. If you are open to equivalent grades under another standard, say so, and list the properties that matter most. Nuroil can quote furnace oil against your stated specification; see the furnace oil page or request a quote.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote