Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read5 sections

Knowledge centre · Water & pool treatment

Sodium bisulphate as a pH reducer

How sodium bisulphate, or dry acid, lowers pH and alkalinity in pools and water systems, and how it compares with hydrochloric acid.

Written by the Nuroil trade desk, Sharjah

On this page · 5 sections
  1. 01What sodium bisulphate is
  2. 02How it lowers pH and alkalinity
  3. 03Dry acid compared with hydrochloric acid
  4. 04Safe use and storage
  5. 05Specifying sodium bisulphate

Most chlorinated pools drift upwards in pH. Liquid and calcium hypochlorite are alkaline, aeration from spray features drives off carbon dioxide and fill water may be hard and alkaline. Operators need an acid to bring pH back down, and sodium bisulphate, often called dry acid, is the granular option.

What sodium bisulphate is

Sodium bisulphate (sodium hydrogen sulphate, NaHSO₄) is a white, water-soluble granular solid. It is in effect half-neutralised sulphuric acid, produced by reacting sulphuric acid with a sodium compound. When it dissolves, it releases hydrogen ions, so its solutions are strongly acidic. It absorbs moisture from the air, so it must be kept in closed packaging.

Technical grades are used in pools and spas, in water treatment, in metal finishing and in cleaning products. Food grades exist for other uses, so buyers should state the grade they need.

How it lowers pH and alkalinity

Added to pool water, sodium bisulphate neutralises part of the bicarbonate alkalinity, lowering both pH and total alkalinity. This makes it the standard tool for two jobs:

  • bringing pH back into the target range, typically around 7.2 to 7.8 under most codes, when it has drifted high;
  • reducing total alkalinity that is too high, usually by repeated acid additions combined with aeration to raise pH again without restoring alkalinity.

The amount needed depends on pool volume, the starting pH and, especially, the alkalinity, because well-buffered water resists change. Product labels give dosing tables; the safe approach is to add a measured, moderate dose with the circulation running, wait for it to mix and retest before adding more. Overdosing lowers pH quickly and can make water corrosive.

Dry acid compared with hydrochloric acid

Sodium bisulphate (dry acid)Hydrochloric acid (liquid)
FormGranulesFuming liquid
HandlingNo fumes; spills can be swept up; still corrosive to eyes and skinReleases corrosive fumes; splash hazard; needs ventilated storage
Strength per kgLower; more product needed for the same pH changeHigher
What it adds to waterSodium and sulphateChloride
Long-term effectSulphate builds up, raising total dissolved solids fasterChloride adds to dissolved solids more slowly
Typical usersResidential pools, hotels, sites that want to avoid liquid acidLarger commercial pools with acid dosing pumps

The sulphate point matters for some pools. Accumulated sulphate can attack cement-based surfaces and grout over time, and because dry acid adds more dissolved solids for the same pH change, pools using it heavily may need more frequent partial water replacement. Many operators accept this in exchange for easier and safer handling.

Outside pools, the same chemistry makes sodium bisulphate useful wherever a solid acid is easier to manage than a liquid one: trimming the pH of small water systems, acidifying cleaning solutions and neutralising mildly alkaline rinse water. In each case it adds sulphate, so check discharge or process limits before adopting it.

Safe use and storage

Sodium bisulphate is an acid. It must be kept away from all chlorine products, because acid in contact with hypochlorites or TCCA releases chlorine gas. Store it dry, in its original closed container, on the acid side of the store with separate spill containment. Add it to water, not water to it, and wear eye and skin protection as the SDS directs. Transport classification depends on the specific product and is stated in section 14 of the supplier's SDS.

Dry acid trades some strength per kilogram for easier, fume-free handling. Dose in small steps, retest, and keep it well away from chlorine products.

Specifying sodium bisulphate

When you enquire, state the grade (technical or food), minimum NaHSO₄ content, granule size if your feeder needs it, pack size and destination. Ask for the SDS and a certificate of analysis. Nuroil supplies sodium bisulphate on request alongside pool chlorine products; see the swimming pool page or request a quote.

KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote