Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read5 sections

Knowledge centre · Lubricants & base oil

Base oil grades and specifications explained

A reference to API base oil groups, common grade names such as SN150 and SN500, the tests on a base oil certificate and typical values.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of base oil storage and blending
On this page · 5 sections
  1. 01API base oil groups
  2. 02What grade names mean
  3. 03Typical properties of common Group I grades
  4. 04Tests you will see on a certificate
  5. 05Writing a base oil specification

Base oil is bought and sold using two systems at once. The API group describes how refined the oil is. The grade name, such as SN150 or SN500, describes its viscosity. A certificate of analysis then gives the measured properties for each lot. This guide explains all three.

API base oil groups

The American Petroleum Institute sorts base oils into five groups:

  • Group I: saturates below 90% and/or sulphur above 0.03%, VI 80 to 120. Solvent refined.
  • Group II: saturates 90% or more, sulphur 0.03% or less, VI 80 to 120. Hydroprocessed.
  • Group III: saturates 90% or more, sulphur 0.03% or less, VI 120 or more. Severely hydrocracked.
  • Group IV: polyalphaolefins (PAO), a synthetic base stock.
  • Group V: everything else, including esters, polyalkylene glycols and naphthenic oils.

For product details see Group I, Group II and Group III.

What grade names mean

"SN" stands for solvent neutral, a traditional name for solvent-refined paraffinic base oil. The number is the approximate viscosity in Saybolt Universal Seconds at 100 °F. So SN150 is a light grade and SN500 a heavier one. Bright stock is a much heavier, highly refined residual base oil.

Hydroprocessed oils are often sold under names such as N150 or 150N, or by their kinematic viscosity at 100 °C (for example a "4 cSt" or "6 cSt" Group III). Do not confuse SN base oil grades with the API "SN" engine oil service category, which is unrelated.

Typical properties of common Group I grades

The table below shows ranges drawn from published producer specifications. Values vary by refinery, so always work from the CoA for the actual lot.

Property (test method)SN150SN500
Kinematic viscosity at 40 °C, mm²/s (ASTM D445)about 29 to 34about 94 to 110
Kinematic viscosity at 100 °C, mm²/s (ASTM D445)about 5.0 to 5.5about 10.5 to 12
Viscosity index, min (ASTM D2270)about 88 to 95about 90 to 95
Flash point, open cup, °C min (ASTM D92)about 200 to 210about 220 to 237
Pour point, °C max (ASTM D97)about -9 to -12about -6 to -9
Appearance (visual)Clear and brightClear and bright

Tests you will see on a certificate

  • Kinematic viscosity (ASTM D445): the defining property of the grade, at 40 °C and often 100 °C.
  • Viscosity index (ASTM D2270): how much viscosity changes with temperature.
  • Colour (ASTM D1500): a consistency and refining check; lower is paler.
  • Appearance: clear and bright, free of haze, water and sediment.
  • Flash point (ASTM D92 open cup or D93 closed cup): handling safety and volatility indicator.
  • Pour point (ASTM D97): the lowest temperature at which the oil still flows.
  • Density at 15 °C: used for blending calculations and converting volume to weight.
  • Sulphur and saturates: confirm the API group.
  • Noack volatility: evaporative loss, important for engine oil base stocks.
  • Water content, acid or base number, carbon residue and ash: cleanliness and refining quality checks.
A typical value on a data sheet is not a guarantee. Specify limits with test methods, and check each lot's CoA against them.

Writing a base oil specification

A practical specification names the API group and grade, gives a range for kinematic viscosity at 40 °C, and sets minimum VI and flash point, maximum pour point and colour, and appearance "clear and bright". Add sulphur and Noack limits where your product needs them, and state the test methods.

When you request a quotation, include volume, packing, destination port and delivery terms, and ask for a recent CoA and MSDS. Nuroil supplies base oils from established producers with a CoA for every delivery; certificate of origin and third-party inspection are available on request.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote